Colors – The Original Universal Fit 1-Inch Lip Spoiler (White)

Easy install. looks good. Make sure to clean the surface really good before installing. I used a heat gun on the adhesive for a stronger bond. Material is a soft rubber so it makes it way easier to work with.

I was skeptical at first. Not sure of the durability or if the double sided tape would actually last. Worth every penny!HIGHLY RECOMMEND! Make sure you thoroughly clean the surface before attachment. I used ACETONE after I cleaned with soap and water. After you clean the surface thoroughly use an Adhesion Promoter. ( purchase on Amazon ). Apply the adhesion promoter approximately every 8-10 inches then press on the EZ Lip 8-10 inches before the adhesion dries. Repeat until your done. This will absolutely give the EZ LIP a more permanent fitment on for car. Once it dries and bonds with the EZ LIP, it will take an army to pull it off...LolI wanted mine to be more permanent so in addition to the adhesion promotor I also used self tapping screws once the EZ LIP was attached. Absolutely flawless!!!!!!!!!!!I have received soooooooo many compliments on both of my vehicles that I've used EZ LIP on. I bought both RED and YELLOW.

This product is a joke. It's overpriced well marketed Foam. Yes, Foam, not rubber. It has absolutely no durability as they claim. If the product comes into the slightest contact with anything, it begins to show signs of use. You would think that since the product is the lowest point of the car they would have used some special material to make it durable as I thought it was. I have not tried the "Pro" version but I'm not about to drop another $40-$50 to find out.I had this product on for less than 2 weeks on a car that was not lowered, and it does not look good anymore. Worst part is that they won't refund your money, instead they offer 30% off the purchase of a new one. Which in my opinion is insult to injury. Stay away from this version of this product it's a waste of money. Unless of course your willing to drop $35 every few weeks or you have a lifted 4x4 vehicle.Here is the response you'll get when you complaint or ask for a refund:"We're sorry to hear this. Due to the nature of this product, the EZ Lip may get damaged over time. The product's durability is dependent on how well it's installed on the vehicle and how you drive. For these reasons, we do not offer a warranty except for manufacturer defects upon receipt of the product.Based on the images, it appears the EZ Lip has suffered some scrape damage. This is normal type of damage given it's flexible rubber composition.We have recently released the all new EZ Lip PRO model which is made from our strongest Dura-X Foam compound and can absorb far more scrapes before it begins to deteriorate. It also has our Patent-Pending InvisEdge feature for a seamless and professional appearance.As a valued customer, the best we can offer you is a 30% discount on your next order from our website. Just use promo code 30off to receive the discount.Please let us know if there is anything else we can do to assist you."

Very strong material it was tested on really bad roads. All happened was it scope out a lot of mud. It was however screwed down just to be safe.

EDIT: Updated review. I purchased the EZ lip in January 2020 and this last weekend, it finally ripped (August 2021). My car is lowered and I try to drive carefully on roads with dips/bumps. There are some roads where there just isn't much you can do. On these roads, I've scraped the lip and for the most part, the lip had held up well. There were a few scuffs on it, but nothing that was easy to see so I wasn't worried about it. However, this weekend I was driving and scraped it (didn't think it was very hard) and it ripped the lip. Moral of the story, it's a good lip... it's cheap and looks good. I'm not out a ton of $$ like I would have been if I purchased a "real" lip for this car. But after this, I'm not sure if I'm going to replace it or not.I've been wanting a lip for the front end of my Fiesta ST but didn't want to spend $$$ on something that was, 1. only for looks, and 2. probably going to meet a few speed bumps eventually.The EZ lip was SUPER easy to install. I left the tape out in the sun on a hot day to get it nice and warm. I cleaned the bottom of my bumper and honestly didn't even do a great job (no alcohol or other adhesive prep). I lined it up before peeling the tape off to get an idea of how I would handle the different curves in the bumper and when I was happy, I started at the passenger side wheel and then, working about a foot at a time, stuck the lip to the bottom of the bumper. I pressed it on in sections, pretty lightly just in case I needed to peel it off and move it. When it was all the way done, I cut the end and firmly pressed the lip onto the bumper. All said and done, took me all of 4 minutes to install, minus the cleaning time.The lip itself is soft. It's made of what feels almost like a foam. I guess I was expecting it to be more rubber-y based on how it looks, but it seems durable enough. It's easy to tear it if you try to rip it, but I don't expect that I'll have any problems on the car.As far as the adhesive, after letting it set for a few hours, I pulled on it... HARD. The bumper moves but the lip is solid. Also, because the lip is made of soft material, I expect that it will actually resist any scrapes with speed bumps pretty easily.For the price, I highly recommend this lip if you're looking for a bit of style. Really adds a lot to the look of the front end for a pretty low price.

Bought this EZLip for my 240sx, installation was pretty straight forward and very easy. Only downside is that the adhesive did not hold after the first wash. It began to sag & come of. Had to use some glue to stick it back on. So far so good