ALITOVE 24V Power Supply 4A 96W AC/DC Adapter 100-240V AC to DC 24 Volt Converter 4amp 3.75A 3.5A 3.3A 3.2A Transformer 5.5x2.5mm for LED Strip CCTV Camera LCD Monitor Massage Chair

I got this to power my Bambu Labs AMS2 Pro. The Bambu power supply for some reason doesn't come with the AMS system and they charge after shipping close to $40. At half the price, this power supply works just as well. I read one review that said it did not work on theirs, but mine immediately recognized the AC adapter and powered on. Now I can heat and dry my 3D printer filament.

I recently purchased a BambuLab AMS 2 which for some reason they don't send with a power adapter. If you try to buy one through bambu they are either out of stock or will take a week or two to arrive. I'm very impatient and didn't want to wait that long so I decided to purchase this one and I can confirm that it works perfectly! It delivers the right amount of power to the AMS 2 Pro and was really easy to use, you just plug it in and it's recognized and ready to go. The cord itself and the power box both feel high quality. Overall I am really happy with the purchase and recommend it.

I have 4 of these adapters all of them working for bambu AMS dryers for a long time now, no issues. Plugged right in and recognized immediately, for half the price of the OEM.

2021-08-08 Increased to 5 star Seller was quick to send me replacement adapters. Just finally got around to the install today. 2021-07-02 5:30 PM Increased to 4 star Both power supplies confirmed working fine. Confirmed it is one bad female adapter connector, and possibly another slightly marginal one. 2nd one gets slightly warm. I would not expect a wire/connector to get warm at all. The one adapter seems to have a short in it. Squeezing ( very gently ) the body of the connector causes LED strip to flicker. Tested both PSUs with both strips and both connectors, connector was the issue. LED strips both OK, PSUs both OK. I have reached out to customer service in regards to the problem connector(s). Also some FYI. Power supplies are barely warm with no load, and according to a watt meter shows 0 watt draw with no load attached. So there is only neglagible loss when the devices connected to it are off. Dim blue LED stays lit when connected to wall power. 2021-07-02 4:00 PM 3 - star Will update review as I test more. Connected it on a test bench to a 47 watt light strand. 1/2 the power rating of the PSU. The provided adapter to wire the lights does not make a good connection with the PSU cable end. Additionally, most worrisome, it gets HOT. It was warm after 2 minutes and I disconnected, triple checked polarity/connection fit. Let it all cool down. Reconnected and let it stay connected for 5 minutes. At that point the adapter was too hot to handle comfortably. As for the poor fit, while connected I watch the power draw into the power supply from the wall outlet. It varies greatly, from 22 to 48 watts. If I squeeze the adaptor connector it will make a slightly better connection and go closer to 48 watts. Jiggle it a little and it drops as low as 20, LEDs flicker a bit. Power draw fluctuating. Bypassing that adapter everything seems OK. Note: I have not connected any dimmers/controllers in line, this is just PSU to LED strip for initial testing. I have 2 of everything for this install, I will test with other units / combinations to rule out the problem, but so far it seems to be the little adapter is just no good.

This was a good replacement for my previous one that blew up. Good price and worked well enough. No real complaints

If you are looking for a power cord for your ams 2 so that you can still using the drying feature while you print from the external spool, this one is what you want. When I plugged it in, i got the little symbol on my p2s screen to show up which indicates the ams 2 pro has a dedicated power source. You cannot dry while you print from the ams, but thats a design limitation. You can pritn from the external spool while your ams 2 pro is drying as long as you have this power adapter. If you dont, the printer will tell you it cant supply enough power to print and also dry the ams. This is a good alternative to paying the for overpriced version on bambu labs official website, plus shipping. Ive been using this for months with no issues at all.

Used for my ams pro 2 from bambu. Half the cost and the ams recognized it. Ordered a second one.

Plugged right in and worked right away. No issues so far would recommend

Me parece muy interesante para hacer funcionar mi taladro

Works great for my HP laptop.

It's a simple adapter. Works as it should. No problems. 5 stars!

This 24VDC supply is perfect for a number of kits, projects, DIY things etc. I am always making small automation equipment it it nearly universally uses 24VDC. This adapter is a quick and easy way to get a good quality power supply. The voltage output is quite stable (looked at it on my scope). The adapter gets a bit warm if you drive it hard, but nothing to worry about. Recommended!

Good quality, works for my fogger