General Finishes Oil Base Gel Stain, 1 Pint, Antique Walnut

I've been entertaining the idea of gel staining my cabinets for a long time, however I never thought it would come to fruition until we decided to change out our kitchen countertops, floors, backsplash. I was thinking on replacing the doors/drawers and just painting it white, however the budget was already creeping up with other expenses and I feel my existing doors would look better as a dark espresso moreso than white. I've read the reviews, read questions/concerns, viewed many tutorials, etc and decided to pull the trigger. I would say our kitchen is on the larger side that includes 25 doors, 15 drawers, u-shaped with a large island. Overall I am happy with the product, outcome and it lived up to the hype. I knew it would require a lot of time and work, but if I could go back I would probably just hire someone. The amount of time it took in total could have easily been paid off by a professional and more if I used what I feel my time is worth based on what I can do to supplement my source of income through other means. On top of that I did sections of it before our kitchen demo/install and after. Since I am away from home for work10-12 hrs per day M-F,I could not be as efficient as I would have liked. I have oak cabinets stained walnut that were about 10 years old. I took steps similiar to many others, but broke it down into 3 sections of the kitchen since it was too large to get down at once. Prep time was probably the most tedious part that included- 1) Empty cabinets, 2) clean cabinets (I used krud kutter), 3) sand cabinets (I tried various grits and found 220 grit to be perfect lightly by hand; if I could go back I would have used a sander), 4) vacuum/wipe down cabinets, 5) tape down areas as needed. Imagine doing this 3 times. I used the sock method (with two non latex gloves). I just bought cheap socks from target/walmart I believe. I also had a small brush and sponge brush. I would the small brush was a lifesaver for the small crevices and corners. I did 4 layers of the Java stain in total. I waited 48 hours first the first coat to dry and 24 hours for the rest. I was expecting some streakiness, but was a little concerned after seeing it on the 3rd coat. 4th coat was the key winner. I think part of that is not optimally preparing some of my surface areas; poteintially due to different amount of protective coating found in different areas of my kitchen. Also the area above my range was probably not cleaned as well as it should have been. I did all my doors/drawers in the garage and numbered each one. I did not sand inbetween coats. After the final coat the stain was beautiful. Even the floor, granite installers, contrator was impressed with the work. The satin gloss is very subtle. I was damn impressed. Then came the clear coating. I waited an entire week before applying it. I then very lightly sanded with highest grit sanding sponge I could find (I believe it was 220) and wiped the dust down. I used wipe on with rag/sock and sponge brush. I found all methods to work great. Very easy to go on and gives you a lot of wiggle room. I initially purchased the GF Gel Top Coat in Satin. http://www.amazon.com/GF-Gel-Topcoat-Satin-Quart/dp/B001F7R320. I did 3 coats on my island and a standalone cabinet and it came out great. It also whitstanded through the demo believe it or not. The satin sheen was similiar to the Java satin sheen and if anything you could see the grains of the oak cabinets a little more. I did not notice it enriching the color significant either. It kept it pretty consistent. I was very happy about the results, but I decided to try another product due to the high VOC content of the top coat (wife is pregnant and insist to use part of the kitchen). Since this was still 1/4 way through I had to be reasonable and ended up purchasing a non-VOC top coat off in satin from another website. This is when it all went downhill. I didn't realize what type of skill is needed to apply a top coat, until I purchased this. It made me realize how good the GF topcoat was. My cabinets looked horrible. I should have tested it out first. It was 10x more diffiucult to apply and my cabinets not only looked streaky, but their satin looked more like semi-gloss. It also darkened the cabinets noticably more compared to the original coating. I thought I ruined my kitchen. I decided to do more research and found that the most important coat is the last coat. I learned better technique and tools and redid a large portion of my kitchen. Luckily my new technique did wonders and I was able to coat it streak free and the sheen was also a lot less subtle for some reason. Possibly due to putting it on thinner and I made sure I mixed it very well. I did 3 coats total. The end result came out great despite the scare. I ended up using 2 quarts and still have a little left over. It took me about 6 weeks solo to do my large kitchen, working full-time and other priorities that I could not push back. Like I mentioned if I could go back I would have just hired someone, but that is only because I can supplement my income in a lot less time I spent doing this project to just hire someone. I think that there are so much variables to consider before just doing it so do your research, be patient and trial and error. Everyone's surfaces are different; different wood, coatings, dirt, details, etc. So understand the optimal way to prep for your actual surface. I also think technique and having the right tools plays a role especially if you have a more challenging surface such as a door with all types of crevices, details, corners, etc. Too me that was the most difficult part was because of those challenging areas of the door. So my two biggest tips would be good preperation for your project and learning the proper technique/tools to do the job. Oh yeah and patience too.

Very forgiving & easy to use. As you can see, it's also very versatile! I used stain on both kitchen cabinets (2coats) &on top of stools (3 coats), with different results based on technique. For cabinets & banister (1 heavier coat), I used a foam brush & they did not get "wiped off" between coats, so coverage is darker, more opaque & more like that of paint. On stool tops & stair treads (3 coats), stain was wiped on using old white socks &, therefore, is more translucent & more grain is showing through. Mantel only got one coat using sock method & the pretty grain is showing through beautifully. Looks a lot like a walnut stain. I'm very happy with the results! Gorgeous upgrades to golden oak without the price tag of a replacement. WIN! A few tidbits: 1- it does have an odor. I have sensitivities to chemical vapors, so I wore a carbon filtered mask & kept windows open while I worked in short time frames & was fine. I then ran ceiling fan & sat outside or ran errands while it dried a bit & the odor dissapated. The one time I took the mask of early to clean up in the kitchen I got a huge headache & did not make that mistake again! 2-Do not go over previous stained spots until they are completely dry (I gave them 24 hrs between coats). You end up pulling the previous stain & you now have a splotch w/very little pigment. Not pretty! Wait, and just add the extra coverage you want on the next coat. Otherwise you just end up pushing the pigment around & it doesn't stick to anything already gone over before. 3-And the BEST tip for last. I put off using this product (& thus my projects) for a long time due to the fear brought about by people warning it stains skin, nails, & basically everything it touches & their horrible experiences of trying to get it off. Well, turns out it's SUPER EASY to get off your body if you use coconut oil! I just scoop a dab from my jar, rub it all over where I have stain (it smears all over & looks like you're just making a bigger mess, but don't worry!!). It then just comes right off & transfers to the paper towel I use to wipe it off. Another WIN! I then did not use my jar for any other purpose, but for this since some stain did transfer from my hand & onto oil in the jar. So I recommend pulling some out & placing in a second container to use specifically for this purpose & not having to sacrifice a huge container of it. Also, I have not had any luck finding a way to get it out of clothing, though, so I do recommend wearing your appointed "Painting clothes" when working with this. Hope this helps & have fun with your project!

I am doing away with all the honey oak in our house - and there is A LOT. I started with the vanity in the bathrooms and then moved on to the kitchen (which is in process now) and railings. This stuff is GREAT. Here is why I like it so much: 1. Once you get the process down it's easy-peasy to complete - just takes time (see below for my process) 2. It's a very rich color - it may look black and at first glance however it is a very dark rich brown 3. I have put the top coat on (GF High Performance water based in satin) for most of my work and it seems to be holding up well - good with humidity (vanities in the bathrooms) and constant use (railings) 4. Keeps my wood grain so it looks more natural than painting 5. What do you need: gel stain, top coat, sand paper, TSP substitute cleaner, lint free rags, foam brushes, drop cloth, painters tape You must have patience while going through the process - not so much for application but making sure you allow sufficient dry time between coats - with proper prep I was able to get to the full dark color in about 3 coats (I may have had to touch up some spots here or there. Here is my process: 1. lightly sand surface (break up the top coat) - if you look online you see folks that say you don't need to sand - while that is true, I found I needed an additional 2 coats if I didn't do this prep - thats more material and another 48 hours added on to my time, so I took the time and prepped properly. 2. Use a TSP substitute (also a deglosser) to help with what you just broke up. I followed directions for diluting the solution and sprayed it on (cover other surfaces!!) and let sit for at least 5 minutes then wipe off with a damp cloth. 3. after that has dried, grab some gloves and crappy clothes and a foam brush and start the application - first make sure you stir the gel stain well and put it on your application area thick - I mean, it looks like you can finger paint in it thick - you shouldn't see much of the actual wood at this point 4. Wait - once you apply the gel stain (make sure not to apply to an area too big - you can't have it dry before wiping off) you wait about 10 mins (humidity, temp etc will affect it) you can start wiping it off. I always brush the foam over my rag to put a little down - if you start with a 100% clean cloth you will take off more material than you want to. You want to wipe it down until it looks like there is no more sitting on top - don't press too hard, some of what set was directly on the wood - but you don't want "globs" of the stuff left on there - I'll try and get a pic of this as I work through my cabinets. 5. Now wait some more - 24 hours minimum to be exact between each coat - DO NOT SKIMP ON THIS or you will not be pleased. 6. After all coats are complete slap a clear coat on there (after waiting 72 hours after last application before clear coat) which thankfully you can get 3 coats on in 1 swoop as there is only a 2 hour dry time (for the GF clear coat) If you're not sure this is for you - pick a small project first, or even just a random board so you know how it goes - it's not for the weak of heart but I do love the outcome and would do it again and have never even considered using another brand of gel stain!

This stuff is amazing!! One thing I wish I would have known, though, is that the Brown Mahogany color has a definite red tone to it, which I was not expecting or wanting. I ended up doing one coat Brown Mahogany, two coats Antique Walnut and I love the way it turned out. I want to make it clear that the pictures I have attached are of that combination- 1 coat brown mahogany, 2 coats antique walnut. I never saw any good pictures of what brown mahogany looked like alone, and misunderstood what color it is-- it is definitely RED-toned. So I topped it with antique walnut which is more yellow-toned, and I love the combination. I didn't want my pieces to be black, like the Java gel stain seems to be. I wanted the gorgeous wood grain to still be visible, and I am pleased as punch at how it turned out. It took some serious tweaking, but well worth it. I gave it a go on a solid oak table my dad made and was passing on to me. I sanded it and two benches down with a 120 grit sandpaper and used the "foam brush- shop cloth wipe off" method. It was a disaster. It was splotchy and looked terrible. Turns out it wasn't my application method that was awful, it was the condition of my wood. After contacting General Finishes customer service, and also posting on a woodworking community board I found my problem was that my dad had previously finished the table/benches with Danish oil. I had not sanded down deep enough to get rid of that oil (same goes if the wood has been treated with Pledge or certain other things they list). It was recommended on the woodworking board to start sanding with 60 grit and work my way up all the way to 220 grit. I wiped the surface down with mineral spirits first, as suggested on the General Finishes video. The stain went on like BUTTER and looks absolutely gorgeous!! I used the sock method this time and it's SO much better than the foam brush method. No need to wipe off with cloth after, and it goes on so smoothly!! A little goes a long way. I will absolutely buy General Finishes gel stain for every staining project I do from now on!!! The picture I attached is of one of the finished benches. One coat Brown Mahogany, 2 coats Antique Walnut. You can see in one of the pictures the other bench to the left in progress. The bottom legs of that bench are the original sanded-down oak. Once everything has been stained, I will finish it later with the General Finishes Arm-R-Seal which has been amazing on other pieces I have refinished.

This stain is such a lovely, rich color. I've really enjoyed using it around my house and continue to find new ways to incorporate it. It does take some time to get used to in terms of applying it, and I would suggest getting good foam brushes and not putting it on too thick. When done correctly. it's absolutely premium and it's protecting my furniture and woodwork so well in conjunction with the topcoat. I'm very happy with how it turned out.

I had never used this product before. We wanted to change the color of the wet bar in the family room and my initial thought was to paint it. My daughter had used General Finishes Java stain to redo all the doors in her house and it looked pretty good. She said it was easy to apply with a sock, foam brush, or bristle brush. I decided to try it. I chose the General Finishes Gray Gel stain. First I removed all the hardware and the doors and drawers. I sanded all the wood with 120 grit and then 150 grit and wiped everything clean with a rag and mineral spirits. After watching many YouTube videos on this, I decided to use a foam brush applicator. First coat went on easy but pretty uneven coverage. No issue as many of the YouTube demos said the same. Though the can says you can re-coat in 6 - 12 hours when the finish has hardened, it took over 24 hours for the first coat to harden, and it was not a heavy coat. I then applied the second coat with a new foam brush and it covered better, but still felt like it brush was dragging over the previous coat, like it wasn't completely dry and smearing the first coat in some places. Still had some areas that were not covered 100%. OK, YouTube said the same thing. Had to wait over 36 hours for the second coat to harden before applying the 3rd coat. I decided to use a bristle brush (specifically for staining) for the 3rd coat and it covered everything perfectly, like I just put on a fresh layer of paint. I think I should have used a bristle brush in the first place. This coat took 48 hours to harden and be dry to the touch. This was in our finished basement with temp control and at near perfect drying conditions per the label. I waited another 24 hours to make sure it was totally dry and handle before applying the General Finishes Gel TopCoat Satin. This stuff then took almost 3 days to be dry to the touch to where I could handle the doors and drawers without smudging and I could then re-assemble the cabinet. PROS: This gel stain is like applying paint and it goes on easily. CONS: 1) It will take 2-3 coats of stain to achieve total coverage, if that is what you want. 2)This stain takes way longer to dry than what the label says, even in near perfect drying conditions per the label. It took almost a week just to stain this cabinet and wait for it to dry before I could apply the top coat. 3) After applying, this gel stain has a gloss sheen to it. I was wanting a cabinet that had maybe a satin sheen at most which I figured I would then have to achieve using the General Finishes Gel TopCoat Satin finish. Didn't happen. The satin topcoat, though it says satin finish, is really more of a gloss finish. The cabinet now has a high gloss finish, which is way glossier than what I wanted for a finished product. Now I will have to wait 30 days for the finish to "cure" before attempting to reduce the sheen with 0000 steel wool. 3) I could have painted the cabinet and been done with this project in 2, maybe 3 days at most and probably achieve the same results. Oh well, it was a learning experience

This is an amazing product!! I recently bought a home that had stairs that were in HORRIBLE condition. The previous owners had pulled up the carpet on the stairs and stained/top coated the stairs with less than desirable results. There was white paint all around the edges of each step with lots of nicks and imperfections. To repair my entire staircase by a professional would have cost so much money. So, I did my research and found this product. I bought the General Finishes in both Brown Mahogany and Java and quickly realized that I only needed the Brown mahogany to get the look I desired. Please keep in mind that I have never done a Do It Yourself home project before so I am an extreme novice and I was able to do this with great results. I only lightly sanded each stair and applied two coats and sometimes 3 depending on how the 2nd coat came out. I waited a full 24 hours after each coat to allow for drying. I then used the General Finishes High Performance in Satin for the top coat. I applied 6 coats of the top coat and I applied the top coat all in evening allowing 1 hour of drying time between coats. To complete the look, I bought textured white wallpaper for the stairs riser and inside corner trim to give a clean straight line at the bottom of each stair riser. Now, I only need to repaint the sides of the stairs white and gel stain the banister. I am 100% satisfied with this product and it completely exceeded my expectations. I found that the easiest way to apply the stain was to spread it on using a foam brush allowing a few seconds to pass before wiping down in a left side to right side motion using men's athletic socks that I bought from Amazon as well. I made sure I wore gloves underneath the sock to help eliminate gel stain from getting on my hands too much. Please do yourself a favor a buy a bottle of Mineral Spirits to help clean up any gel stain that gets on your hands and/or areas where you don't want the stain to appear. No matter how hard you try to prevent it, you will get gel stain SOMEWHERE. You can also use the Mineral Spirits to wipe away the stain if you feel you have messed up. As long as the gel stain is wet, Mineral Spirits will work for cleanup. Please make sure you have a clean surface before applying the gel stain. I just used a type of wet wipes and I spread a thin layer of Mineral Spirits on the stairs to allow the gel stain to be applied smoothly. I learned this trick from the General Finishes application videos. I am attaching a bunch of photos for you to get a good idea of how the gel stain looks on stairs as I didn't see too many folks try this with steps. So for those of you wondering if this can be done on stairs, it has worked perfectly for me. And while my stairs are not perfect. The are a 100% improvement from what I started with and for that I am very grateful for this product.

General Finishes makes a great product. This thick gel was easy to work with and nutmeg is my color.