I would like to use this to cut the power on my winch when not it use. Does anyone know if this will handle the draw when the winch is in use?

Check your winches max current draw at it's max pull. Most 10k winches can go over 300-amps easy some over 350-amps. Always use switches, contact points and terminals that can handle more than your devices rated maximum current draw and max voltage, even if it's only 10% more. Don't size for nominal loads, size for max current and max voltage plus a safety factor. Wire charts (current to awg wire size) is a safe minimum size. If it says 4awg wire, go to 2awg. Copper is cheap and it will lower your circuits overall resistance and current draw while being safer. Do this and you wont get suprised the general wire chart that is probably written for a very spoecific type of wire strand size, jacket, etc. You can go down in fuse/breaker size, it will just blow/trip more often. You can go up one fuse size and, at this current level, that means only 10-amps more. So if your winch can draw a max of 300-amps, the largest fuse you should use is 310-amps. Momentary is very subjective. Without a quatitative number, size components for maximum current draw. Also, NEVER put a switch on a Negative, Common or Neutral wire.

can this be used with 4/0 cable lugs

The switch doesn't care about the lug current capacity, just about physical characteristics of the lug, which unfortunately is not standardized. If the lug is bulky at its connecting area to the cable, some allowance might have to be made in mounting. The lug needs a fairly large hole opening where it connects to the switch, at least a 7/16 inch hole. The metal area around the hole opening of the lug can't be too large or it will short out to the connector on the other side of the switch, so some grinding of the lug's squareness might be necessary. Available thread on the switch terminals is more than adequate for a fairly thick lug.

I bought this to hook up to my rv battery case. i assumed it would come with instructions. does anyone have a good website showing how to hook it up?

Really no need for instructions. I installed it in my camper, its purpose is to disrupt electrical connection. If you have one main power cable then connect from the battery to the switch and then main power to switch. If there's a bunch of connections to the power side and not sure then you can also install the switch on the negative side which usually goes to one chassis ground.

ASIN	B07T288VN8
Actuator Type	Rotary
Best Sellers Rank	#470 in Automotive ( See Top 100 in Automotive ) #1 in Automotive Replacement Battery Switches
Brand	Nilight
Circuit Type	1-way
Color	On-Off Switch 275A
Compatible Devices	Car, Marine Boat, RV, Camper, Travel Trailer, Truck, ATV, UTV, Battery Banks
Connectivity Protocol	X-10
Connector Type	Plug In
Contact Material	Alloy Steel
Contact Type	Normally Closed
Control Method	Touch
Control Type	On/Off
Current Rating	455 Amps
Date First Available	June 12, 2019
Global Trade Identification Number	00812227031862
International Protection Rating	IP66
Item Weight	1.6 ounces
Item dimensions L x W x H	3.86 x 2.87 x 2.83 inches
Item model number	90015A
Lower Temperature Rating	1 Degrees Celsius
Manufacturer	Nilight
Number of Items	1
Number of Positions	2
Operating Voltage	48 Volts
Operation Mode	ON-OFF
Product Dimensions	3.86 x 2.87 x 2.83 inches
Terminal	Marine
UPC	812227031862
Unit Count	1.0 Count
Upper Temperature Rating	1 Degrees Celsius
Vehicle Service Type	ATV, Passenger Car, Trailer, Truck, UTV
Wattage	21760 watts

Nilight - 90015A Battery Switch 12-48V Waterproof Heavy Duty Battery Power Cut Master Switch Disconnect Isolator For Car Vehicle Rv And Marine Boat (On/Off),2 Years Warranty

Details

Description

Specifications

Reviews

Common Questions