SYLVANIA Headlight Restoration Kit - Long-Lasting Headlight Repair Kit for Restoring to Like-New Condition - Surface Activator, Exclusive UV Coating, Clarifying Compound & More - No Tools Required

My headlights were completely clouded over and oxidized, significantly reducing my visibility at night. I decided to try this kit before spending hundreds on new housings, and I’m glad I did. Complete Kit: This came with everything advertised. The instructions were very clear and easy to follow. User Pro-Tip: While the kit is comprehensive, I highly recommend using a separate spray bottle with water for the wet sanding steps. Keeping the surface constantly lubricated makes the sanding much more effective and prevents the paper from loading up. Effort vs. Reward: It took about one hour to do both headlights. It definitely requires some "elbow grease" during the wet sanding stages, but don't rush it—the more effort you put into the prep, the better the final result. The Results & Durability: The transformation was night and day. The lenses went from hazy and yellow to crystal clear. Most importantly, it’s been three months since the application, and they still look brand new. It has held up perfectly through harsh winter driving (salt and slush) and several trips through the automatic car wash. Final Verdict: 5 Stars. If you’re willing to put in the manual labor for an hour, this kit will save you a fortune. The sealant actually lasts, which is the biggest factor.

I own a seventeen-year-old Toyota Yaris hatchback (152,000+ miles), which has been parked outside in the sun and elements all of its life. I'd already had the headlights resurfaced (by the Toyota team) many years ago—but my headlights were, by this point in time, at the stage of not passing annual inspection. Replacing both headlight units at the dealership (including labor) would have cost in excess of $700, so I figured—why not try this, and see what happens! The results are really terrific. As "like new" as you're going to get with a seventeen-year-old car which is parked outside. Here would be my observations having just done this project this morning (without access to a hose, mind you!). The instructions are worth reading a couple of times before you take-on the project. It's, actually, a lot easier than the very detailed instructions might imply. Just go step by step, doing each step to both headlights before you move on to the next step, and you'll be fine. 1) Bring lots of water, and a spray bottle (as recommended in the instructions). I filled up some clean milk-cartons I'd saved for the project, and just refilled the spray bottle from those as needed. Super easy. I used about three milk-cartons of water (1.5 gallons). You'll need lots of water-spray as you sand with the provided grades of sandpaper. I would recommend starting (with the first grade of sandpaper) with light to medium pressure, then move to more consistent medium pressure. The second and third grades of sandpaper really are very smooth and fine, and you can finish-off the third grade of sandpaper with a really light pressure. Be patient, and go for a truly smooth surface. I did the recommended circular motions both clockwise, and counter-clockwise, to ensure the smoothest possible finish. Worked like a charm. 2) Regarding the activator spray (with which you will start and, toward the end, use again): I used about 2/3rds of the spray on the first stage (both headlights), dissolving the initial oxidation and grime. I feared I'd not have enough with just 1/3rd by the end, but I had plenty. I'd bring a soft sponge, too, just to ensure that you get the lenses fully clean between steps. I found having extra soft, clean rags helpful with drying as well. 3) Painter's tape definitely protects your paint around the headlight, so take the time to mask-out your light, and protect your paint. The only thing I'd suggest, is to spray-clean your paint-surface after your remove the painter's tape following use of the polishing compound. Some of the polishing compound gets under the tape, so just give that a rinse before you dry the lenses and apply the final UV gloss-coating. Keeps things neat and clean around the lenses. 4) As for the gloss-coating: you really can be very generous applying it to the provided blue-cloth. I was a tiny bit stingy on the first headlight, fearing I might not have enough product for the second headlight. Don't worry ... you'll have plenty of UV product left over when you're done. I'd really soak the entire blue-rag well, and apply generously. I can see a *very* tiny difference between the first headlight I did (where I was more stingy applying the UV gloss-coating) and the second (where I was more generous). It's so slight you'd never see it. Just rest assured that you'll have plenty of UV gloss by the end of the project, as it spreads evenly, smoothly, and well—so be generous in applying it. The best part? If I get any haze again, this was probably the easiest headlight-repair imaginable. I'll just do it again! And I saved about $700 to boot. You just need to set aside the time to do each step well and carefully. It took me perhaps an hour and a half from start to finish (and I was moving slowly and carefully), with some time thereafter cleaning up and just standing around to ensure no falling autumn leaves fell on the UV gloss while it was still wet. Just went to check on the headlights, and they're completely dry to the touch, and very smooth and glossy. This is a terrific product! Easy to use, great instructions, and a really fine result. I look forward to seeing the longevity of the product.

I usually foul up these projects, but this worked surprisingly well. Short version - the headlight really does look "like new" after I finished! I only had one headlight to do since the other one had been replaced due to being broken. Some notes on the process: Read ALL of the instructions FIRST! Basically you will need to prep BOTH headlights before doing the very last step, because there is only one included applicator for the last step. Other than that, the instructions are straightforward. I masked off the headlight with painters tape, before doing anything else. This is important otherwise the sandpaper steps could damage the paint right next to the headlight, if you even lightly brush the paint with the sandpaper. Also, while the kit is supposed to be safe in case it accidentally gets on your paint a little bit, why risk any affect on your paint at all? The first step is a big part of the magic here. I thoroughly cleaned the headlight before starting, but the first step loosened up so much grime and surface contamination that my wiping cloth was FILTHY! It really softened up the contamination and surface deposits, which probably saves a ton of time sanding and polishing in the next step. Because I had plenty of fluid and was only doing one headlight, I did this step twice. The second time I didn't get nearly as much contamination on the rag, so doing it once per the instructions is probably fine. The second step took a while because I'm a perfectionist and took extra time making sure I evenly sanded the whole headlight all the way to the edges. I think this paid off, but it added extra time for 2 reasons. First, it took time carefully wet-sanding the edges of the headlights using small circular motions in order to avoid creating lines and gouges in the headlight. Second, since this is a wet-sanding process, the painters tape may come loose due to the water. Trust me - it is WORTH IT to stop, dry everything off, and re-apply the tape so you don't ruin the paint on your car next to the headlight! So I stopped a few times to re-apply the tape mask. The only minor critique of the kit itself was that the step 2 polishing paste comes in a single packet that you cut to open. So you need to do both headlights at once otherwise you'll end up wasting half of the polishing paste and not have any to do the other headlight. Also, the headlights on my car are pretty large and I think I would have had to really skimp on the paste in order to polish both headlights with the paste. Since I was doing only one headlight I could be liberal with the use of the paste, but even using "just enough" I think I might have not had enough for the second headlight. Still, my headlights are unusually large and it still might have been barely enough, so the kit will still work for both headlights. I'd be much more comfortable however if Sylvania had simply included 2 slightly smaller step 2 polishing paste packets instead of one larger one that has to be used for 2 headlights at once. After step 2 polish, the whole headlight looked kind of like frosted shower glass, except that even though I took my time to do the sanding and polishing right, I could still see sanding swirls and some uneven remaining oxidation. I figured I had nothing to lose though, so I proceeded to the third step in spite of not being 100% happy with how I had done the preparation. Remember, I usually foul these things up somehow, so... I was AMAZED at how well it looks after the third step! This is the second magic part of this kit. The step 3 solution went on very easily with the included applicator. A tip - follow the instructions EXACTLY, including resisting the temptation to go back and "touch up" sections that don't look quite right after the application. I had to dab/wipe on a bit near a corner where I didn't smoothly apply the final coating on the first swipe, and if I look VERY closely I can see that the coating is thicker and not very even in the places where I went back a second time. Bottom line, pretty much soak the applicator with the fluid, make one pass over every part of the headlight, and LEAVE IT ALONE without even thinking about making second coats! After the application, it was immediately obvious that it came out looking great. When standing just 2-3 feet away, the headlight looks just as clear as the brand new one on the other side, and there are no visible scratches or hazing at all. Even the area where some of the original oxidation damage was uneven after sanding came out looking crystal clear. If I put my face 6 inches from the headlight and shine a light on it just right, I can see the coating in the areas where I had to go back to cover places on some curved edges that I didn't get with the smooth application swipes, but those are the only areas where I can even tell anything has been done at all, and my face has to be right up close to the headlight. From a few feet away, it looks brand new. Time will tell whether or not the finish stands up to the sun and heat, but the initial results are amazing. Follow the instructions, take the time to protect the paint during steps 1 and 2, do steps 1 and 2 on both headlights before step 3 (and remember that step 2 packet must be split for both headlights) and resist the temptation to apply second coats of step 3. Do that, and you'll have great results too. Highly recommended, and good luck with your headlight restoration!

This is the third time these headlights have been restored. Wait, let me rephrase that. This is the third ATTEMPT to restore these headlights. The first time the dealer cleaned them up a bit so it would pass the bi annual safety inspection. It lasted almost one year. The second time I did it myself with another brand of restoration kit. It got them clear enough to pass another safety inspection but I wasn't very pleased with the result. This time I did some more research and found this Sylvania Headlight Restoration Kit. It was highly rated and Boy! were they right! As you can tell from the before, during and after photos I've included this kit really works. Except for a couple of pretty deep stone... um dents I'll call them because they're not really chips, the headlights are as good as new. I very definitely recommend this kit to anyone that wants to have headlights that shine like new without the expense of replacing them. Now, that being said, I have some advice. Follow the instructions! They are very clear and take you through the whole process step by step. Do not try to hurry through. If it says it should take about five minutes of sanding for this step then set a timer and sand for five minutes. When it says keep it wet, keep. it. wet. I used a garden hose with the nozzle set to a heavy mist and sprayed it every 10-15 seconds. This rinses away the slurry and cleans the sandpaper so that it keeps cutting. If you don't keep it wet the sandpaper will clog up and you will just be wasting your time and energy rubbing your headlight. When you get to the last step, the UV blocker, don't skimp on it. There is lots in the kit to do two large headlights. Don't rub it on in a circular pattern. Use straight strokes from one edge to the other. Don't rub it on back and forth. Start from one side and wipe to the far side, pick the cloth up and then make your next pass slightly overlapping the first. Continue until you have completely covered the lens and then STOP! DO NOT go back over it and DO NOT TOUCH it. Let it dry four to six hours. Now enjoy the fruits of your labour. Your brand new-looking headlights for nowhere near the price of new headlights.

Excellent product for DIY. It works as it claims, need to be very careful when applying clear coat, do not over apply.

By following the instructions, this kit really works. Though intended for 1 car, I think it can do 2 cars.

Works really well. Have restored headlights to nearly new looking. Can’t comment on durability as I have only just used it.

Clean like new and protected headlights from uv