Stan's NoTubes Rim Tape for Rim Interior (21 MM)

I’ve been using Stan’s NoTubes Rim Tape for my mountain bike tubeless setups and have found it to be a dependable choice. The tape is available in various widths (21mm to 39mm), allowing for a good fit across different rim sizes. When applied correctly, it provides a durable, long-lasting seal that doesn’t leave sticky residue upon removal. Pros: • Effective Seal: Once properly installed, the tape maintains air pressure effectively, even under rugged trail conditions. • Clean Removal: Unlike some alternatives, it doesn’t leave behind adhesive residue, making maintenance easier. • Variety of Sizes: The range of widths ensures compatibility with most rim dimensions. Cons: • Installation Requires Precision: The tape lacks flexibility, making it less forgiving during application. Ensuring a clean rim surface and applying the tape with adequate tension is crucial to avoid air bubbles and ensure a proper seal. • Not Ideal for Non-Tubeless Rims: Users attempting “ghetto” tubeless conversions on non-tubeless rims have reported challenges in achieving a reliable seal. Tips for Best Results: • Cleanliness is Key: Thoroughly clean the rim with isopropyl alcohol before application to ensure optimal adhesion. • Proper Tension: Apply the tape with firm tension, pressing it into the rim bed to avoid air pockets. • Layering: For pressures under 45psi, one layer suffices. For higher pressures, a second layer is recommended. Final Thoughts: Stan’s NoTubes Rim Tape is a solid choice for riders with tubeless-ready rims seeking a reliable seal. While the installation demands attention to detail, the performance payoff is worth the effort. However, those with non-tubeless rims or seeking an easier application process might explore more pliable alternatives

Kind of surprised at the negative reviews and it made me second guess going with Stans tape. But I went ahead and purchased since it was the only rim tape I could get delivered next day. I have a set of Stans Arch MK3 tubeless ready wheels which had already been set up tubeless when I purchased them 2 years ago. After getting my tired punctured recently I put on a new tire but I kept losing air. Once I realized it was leaking through the spoke holes I pulled the tire off and found that the existing rim tape was ripped in places (I guess I was too aggressive with my tire levers when I initially repaired on trail. It was also folded in certain sections allowing air to escape through the spoke holes. So I stripped off the existing tape and spent a good deal of time cleaning the rim to ensure a good adhesion for the new tape. This entailed removing all the old sealant off the rim (after washing with Dawn I used Goo b Gone to get rid of the dried sealant) and then using rubbing alcohol around the entire rim. After I was satisfied that I had removed all the old sealant and any fibers from the rag I was using I was ready to tape. Applying the tape (I used 27mm tape for a 25mm inner width rim as recommended by Stans) was pretty easy and I had no problem whatsoever with adhesion. I also only used one layer with a slight overlap over the valve hole. I then pressed down on the tape going over the edge on both sides around the whole wheel as well as over the center just to ensure the tape was as sealed as I could make it. Put the valve in and secured with the nut. Put the tire back on using the sealant that was left over before I swapped the tape. Inflated to 35psi with a hand pump and had no issues getting the tire bead seated. Checked for leakage and couldn't find any. I'll ride later today but don't expect any issues. Only reasons I can think of why someone had issues would be the following: (1) Do you have "tubeless ready" rims and tires? If not, this tape will not work. (2) Are you using the right tape width for your rim width? Tape should be slightly wider, i.e. 2mm. (3) Is your rim TRULY clean? Like anything else adhesion will not be good if the tire (or your hands) are not clean and free of oils/grease/dirt/dust. (4) Has the tape been stored properly? As soon as I peeled off the first layer of tape from the roll I could tell it was "sticky" but I know that if I left the roll in my garage for several seasons it would probably not have the same adhesion characteristics. For those new to running tubeless there are lots of videos out there that walk you through these steps.

Stan’s has been my go-to for tubeless since I made the switch. This rim tape damn near perfect and, when used correctly, goes on with with no bubbles or hassles. Plus, it cleans up well in case you need to remove it. Ok, to the point of the people saying it goes on lumpy or crinkled or full of air bubbles, here’s the deal: You. Have. To. Clean. Your. Rims. Thoroughly. And I mean it. Every speck if dust, grease, body oil, old sealant, or adhesive needs to come off your rim. That’s true for any tubeless tape. This is a long process. Expect to spend at least an hour per rim getting it spotless. Plus, application technique matters a lot as well. I use acetone to make sure the rim surface is properly prepped, and still pull up a Park Tool instructional video to make sure I’m applying it correctly. Take your time, do it right, and this tape is an absolutely ideal choice for your rims. Ride safe!

初めて自分でホイール（ROVAL）につけたが、簡単につけられた。 ビニテを貼るようなもので、工賃かけてショップでやってもらってたのがあほらしくなった。

Sirve para preparar llantas para tubeles. Un rollo de largo me ha dado para una rueda de 26" otra de 29" y para la tercera que también era de 29" me ha faltado muy poquito y tuve que seguir juntando con otro rollo. Supongo que si hubiese dejado menos margen en las dos primeras me hubiera dado suficiente para las tres (en las primeras dos le he dado mucho margen pisando el principio con el fin). Hay que estirar bien la cinta al colocarla para llegar a deformarla sobre el perfil del aro. Lo he puesto en llantas de MTB de ancho normal (XC), la de 26" tenía ancho interno de 19mm y las de 29" algo más anchas (posiblemente 22mm). Usando liquido X-Sauce y valvulas No Tubes sella y talona bien si se dispone de bomba con mucho caudal (con la bomba pequeña imposible).

Ottimo. Già conoscevo il prodotto.

Wir haben zuerst ein Tuch welches einen Riss hatte. Wir haben das Produkt ohne Probleme zurück verschickt und wir haben ein neues Tuch bestellt. Diesmal war alles super, das Tuch macht genau das was er machen sollte. Wir haben auch draussen ausprobiert, wie lange das Tuch kühl bleibt. Beim 37 Grad war es ungefähr 2 Stunden Kühl und feucht. Ein gutes Produkt für einen guten Preis.

Buena cinta. Cumple con la función.