CORSAIR 7000D Airflow Full-Tower ATX PC Case – High-Airflow Front Panel – Spacious Interior – Easy Cable Management – 3X 140mm AirGuide Fans with PWM Repeater Included – Black

This case is a GEM. I have built a few computers so far in my life, and I think this was the easiest case to build in yet. Though it is a Full-Tower case, so with all the real-estate, it better be easy! The case is Big, it weighs in at a whopping 49 Lbs. empty. However, with my whole build it easily tips the scale at 85-90 lbs. The pictures do not do this case justice, it is BIG, and has a large footprint. Standing at around 2.5 Feet tall, almost 2.5 feet long, and 10 inches wide, you need to make sure you have the space for this case! The chassis is made of thick gauge steel, and feels and looks durable. The metal panels are also thick, and quite hefty, requiring two hands to comfortably handle and maneuver. However the panels are easy to remove on both the sides, front, and top. The removable racks for fans is a very nice touch that made installing the Rad, and fans a breeze. I only used one tray for my LTS 3.5" HDD and the rest of my storage is done through NVMe SSD's. however if you plan on using all 6 trays you will have to be meticulous in cable management because it doesn't leave much room for extra cables let alone using 2.5" SATA drives, so I recommend getting a modular PSU for this case. If you fill your fan slots with corsair fans (I had 12 in total) the cable management bay is a tad bit on the cramped side for the size of the case, but it is workable if you have enough time and patience. I will list my build below to show what I have living comfortably in this tech mansion. The amount of cutouts for the cable routing is very nice in such a large case, there are a couple things I wish I'd done differently. If you like the RGB features like I do, I recommend spending the extra money on Corsair Link systems. It alone would cut the amount of cable routing by nearly 75% and you wont wind up with a rats nest of cables. The commander series of fans have short cables and required some ingenuity to route them to reach the Commander Core and Commander Core XT Modules for all the effects. (mine are still not in order and I spent the greater part of 8 hours on cable routing and management and I'm not 100% happy with where I wound up). However, I'm willing to admit that I went haywire with the RGB fans and went for the less expensive Non-LINK fans so it is mostly my fault. If corsair Were to supply or Offer a kit of a few extension cables for your front fans for the RGB and PWM cables this would work out just fine and It would have saved me a few hours of Cable Routing, however I am not attempting to say this is their fault by any means. Their cable management system provides 2 channels to route cables with Velcro straps to fasten the cables to the chassis. These Channels are small, however, and tend to give troubles for high end power hungry motherboards as their custom cables have the capacitors that eat precious room in these channels. Other than the options for cable management, this is a very nice looking, functional case that is built very well and seems to carry the expected Corsair quality. I 100% recommend this case if you are in the Market for a sleek Modern case to house your large components and give plenty of airflow to keep your expensive parts cool. My Build affectionately named Nightingale: - Corsair 7000D Airflow Black - ASUS ROG Crosshair X670E Hero - AMD Ryzen 9 7900x (AM5) - Corsair Dominator Titanium DDR5 32Gb x 2 - Sapphire Nitro+ AMD Radeon RX 7900 XTX Vapor-X - Corsair RM1000e Modular PSU w/ Corsair Pro Type 4 custom sleeved cable kit - Corsair H170i Elite XT LCD 420mm RGB Liquid CPU Cooler (Top Exhst) - 8 x CORSAIR iCUE SP120 RGB ELITE (4 x on the front panel & 4 x on the side panel) - 1 x CORSAIR iCUE SP140 RGB ELITE (rear Exhst) - Micron 3400 512 GB M.2 NVMe SSD - Crucial T700 2TB Gen5 NVMe M.2 SSD

it has a very robust material and a lot of space inside with tons of different options that i didnt get to discover them all yet after a week it has an insane amount of airflow and at the same time you cant hear anything that comes from the PC ive installed 14 noctua fans and the case is around 60cm away from me and i cant hear anything from it I compared this to my older case (H500P mesh) the difference on noise and temps is too much on my opinion theres few advices that id like corsair to add or change into this case: add a bit more of room for a 4th 120mm fan at the top of the case, the front and side panel can have 4 but not the top and this could make it "match" the whole case (this may make the case overall length bigger so i understand they didnt made it for 4 120mm fans) add a support for the GPU on normal mount (im not sure if its needed for riser mounting) add a screw for the PSU and motherboard door,sometimes the cables need to be pressed a bit to fit and with a magnetic door that isnt possible, this is solved by just taking it off and using the side panel to close it but then this door loses its purpose this case still has more potential to become even better than it is right now and i hope corsair doesnt forget the full-tower designs because this one is GREAT note: you can connect the fan hub that comes with this case as long as the fans you want to install doesnt go over 12w without using the sata connector, if you do you must connect the sata connector (check how much power each of your fans requires and add them all) this is a rule in general for all fan connectors except for some premium motherboards that allow more w in one or two connectors but the rest will still support only 12w note2: if you want to install a 6 fans radiator on the front you have to change the direction of the rails or whatever it is called for it to fit, i didnt try this for the top mount but it should be the same note3: i couldnt find a good position for the SSD's on the HDD's storage without bothering the fan at the bottom located at the side door, i think it was just me not doing a good cable management to fix it and i wasnt expecting it to happen so to anyone that wants to mount a 4th fan for the HDDs/SSDs be careful on the way you set the cables the only "bad" thing in this case is its weight, way too heavy but thats because of the good quality of the case, best way is to take off the side doors and then it will be a bit lighter to carry then put them back after if they make a better version of this it will be on my wish list for sure

Huge Case! I absolutely love it. I slapped a 360mm AIO fan on top, so much space. Case fans are super quiet, and the little holes for cable management is clutch. Glass panel is nice to look at your RGB's if you have it. GPU brackets are nice and tight, too. So much so, you might not need the brace to dodge GPU sag. Price tag is a bit steep, but I found it more than worth it. This is especially true with the newer GPU's being so huge.

Very well made case, bit over kill in places like double back door, plenty of room to put stuff, i got 420 Radiator CPU cooler and a 240 GPU cooler, 16 fans in total all runn fine, keeps the noise down because of solid materials, heavy at 18kg without anything in it, so be prepared to heavy lift (25KG) when fully built.

This case is big. Really big. It also looks real nice, and has very good airflow, and the side panels are on hinges, they open up nicely. There's enough room in this for the largest CPU coolers and graphics cards. It was also really easy to work with for my first build, I was weary about spending so much on a case for a PC, but after building my setup and using it, I'm gonna say it was well worth the money. Ordered a beast of a case, got a beast of a case, 10/10 experience working with it.

Galet stort, plats för allt, fint luftflöde och mycket enkel att bygga i. Topp notch.

Ok to start with this is the best case i have ever had, also the biggest by far but it gets the job done, so there is a couple of things to know about this case, firstly is that the side fan mount only supports 4x 120mm and not 140mm fans. More than sufficient, also when i first used this case it did sound like a jet engine roaring, this was due to the built in fan splitter and my bios settings. The built in fan splitter must be powered by a sata power cable (same as the ssd to power supply cable), the issue turned out to be that the header i used for the fan was set to DC and not PCM, this meant it was firing all fans at max speed instead of a controlled curve. This one change in my bios made all the difference. Cable management has a lot of room and mounts for the fans come off completely for easy fitting of fans, just make sure when you mount the fans they are in the correct orientation and the cables are in the correct position to allow tidy cable management. You get some complimentary screws and tie wraps plus velcro cable tidies which is great, i never used a manual to figure out how to set up the case for my build as it was self explanatory and things are built in a way to make your life easier. I suggest you pick a place with a lot of space for your build as these doors open on hinges and i needed half a room to have both doors of the case open at the same time, i also found that my power supply cables were not long enough to reach things like my cpu and even my 24 pin so i did have to buy a cable extension kit to get around this. Also although i had lots of room for cable management i still found myself fighting with cables, this was due to cable extension connections being at the back, also the fact i am using a lot of fans. I moved the rear stock fan to the front so the front has 3 140mm stock fans, the rear has a noctua 140mm fan, the top has 3 noctua 140mm fans and the side has 4 120mm fans so you can imagine i am running a lot of cables. (case only comes with the non rgb 3 stock fans, the rest i bought separately) Although i needed to buy a PCU extension kit, change a bios setting, fight with cable management i will say this case is definitely worth every penny, it is very well made, strong, everything is designed to make your life easier, it looks great, it keeps my temps low on cpu and gpu and has plenty of space for anyone wishing to run a custom water loop. I only mention my building issues as i wish i knew before i started so i didn't have to wait an extra day for cables and google the hell out of the fan splitter to find it was a bios setting so i hope someone will read this and it will help them if they need it, otherwise my advice is, DEFINITELY buy this case, it is amazing!

Mainly good but slightly over engineered. Focus could have been done with it in other areas. It can be a little form over function.