AR Blue Clean, AR630, Heavy Duty Electric Pressure Washer, 1900 Max PSI, 2.1 GPM, Adjustable pressure gauge, Safe for Water up to 140 ̊

Habia visto muchos videos sobre esta máquina y en todos los videos se puede ver que es una máquina de paro automático cuando sueltas el gatillo de la pistola pero en esta máquina no es así, la clavija de de energía la tuve que re emplazar por otra ya que la que vino instalada en el equipo no sirve ni para México ni para Estados Unidos, la última cosa que percibí es que el switch de encendido y apagado es diferentes al del modelo actual, este switch es de perilla y el de las máquinas actuales es de botón protegido contra agua, no se a que se deba que la máquina venga un poco diferente, probablemente las versiones que se venden en Europa sean así o tal ves esta máquina sea modelo antiguo no lo sé. Fuera de eso la máquina es completamente igual y hace exactamente lo mismo que las otras máquinas AR Blue 630

I'm going to compare this machine to the one it's replacing just to put it in perspective. My old PW served me well for over 20 years and cost under $300. It was a Landa ZF-2 prosumer grade and it actually still puts out quite well but it leaks all over the place so you have to turn the water off every time. I doubt rebuilding parts are even available so ... 20+ years ... it's time. It sure doesn't owe me anything! So compared to that this machine is even better built (especially with the bronze pump body as opposed to the aluminum one), weighs more and puts out a little more. I had slightly modified the wand on my old Landa with stainless quick connects so I could also use a foam gun and separate nozzles plus whatever else comes along. The problem with the Landa is that in using any of them they would cause the unloader to cycle. I don't know if it was a faulty 20 year old unloader or if it's just the way it was set up, but it didn't like the smaller orifices of my attachments. So I'm using my old wand from that machine on this new one because, my one complaint, the wand that comes with this machine doesn't look like you can separate its components to install the quick connects to allow me to use my other accessories, and I like to have options. I'm happy to say my foam gun, nozzles, etc., work great with this machine, and, I don't know how "much" more pressure I'm getting but the arm-dyno tells me this AR630 is putting out a noticeable increase in pressure over the old Landa. It's a bit noisier than the old one but still makes only a fraction of the noise you get from a gas powered machine. Overall this appears well built, heavy, and should have no problem (hopefully) giving me as much service as the old one did and then some. My only complaint really is that the wand doesn't seem readily adaptable for accessories (I just haven't bothered to see what it takes to get it apart, my old one was just fine) but a different wand is easy to acquire anyway. It's not cheap compared to the box store machines but, unlike those, it's a "real" machine too. I use all my shop equipment regularly at home so it usually pays to step up and spend the extra money at the start. I mean, who else gets over 20 years out of a pressure washer? 20 years from now I'll probably barely be able to turn the thing on!

Even with some minor flaws, overall it's an excellent commercial level machine. It's powerfull, pretty quiet compared to consumer machines, and very heavy! The triplex pump will last for decades. I bought it to do car detailing and it deliver a lot of GPM, about 2.3 @ 1000psi with the proper nozzle setup. The gun is decent. Better than what comes with consumer level machines. The hose is cheap and way too short. And it doesn't have any quick connect at the hose end so you cannot turn the gun once the thread are tighten. I upgraded to a 75ft MTM hose with quick connect and an MTM SGS28 gun (swivel handle). The machine setup is now perfect and a breeze to use!

Very pissed off. Bought this unit in the middle of winter, it stayed in my basement packaged up in the original box because of cold weather. Finally have some warm weather and I discover the unit given to me isn’t the same as the ad. The add states they are selling a TSS version of the product, which mine ISN’T. I would like them to take the product back.

The machine has a large plug with a reset button built into the plug. All good, except the plug is not designed for US outlets. A small detail that they forgot to mention. And, so I had to return it. It is heavy, so loading it in the car and taking it to UPS, not so easy. Now, that said, I know this machine is made with a US standard 110 plug, just not from this vendor. Buy elsewhere. The plug is a 20Amp plug and all US homes have 15 amp plugs. A 20 amp plug has one on the prongs going sideways instead of vertical. Machine is made in Canada, thus the problem. Do not buy unless you understand this and happen to have a 20amp outlet, not likely.