2 PIN Small

Good connectors, definitely can get the job done.

I've used a lot of these for outdoor lighting projects and they've worked very well. They're easy to use, work reliably, and look good. I haven't had any issues with signal integrity, water intrusion, or overall fit and finish. There a little expensive but I consider BTF-Lighting to be a more reputable manufacturer so you're paying for the consistency of product and quality.

I've bought lots of BTF products in the past and have never been disappointed in their quality. These are no different in that respect. However, I bought these connectors because I thought they would be compatible with my mini - xConnect trim lights. THEY ARE NOT Mini-xConnect Compatible. The thread diameter is different; the pin locations are different, and the wire gage is 22 AWG instead of 18 AWG. So, while they are great connectors, these will not work if you need the smaller "xConnect". Some of the other reviews indicate that the standard size BTF connector may fit the standard size xConnect connectors, but again these "BTF 3 Pin Small Size" connectors are not mini-xConnect compatible

Waterproof, durable, and easy to use. They come with enough wire length to run through a cable gland and still have space on both ends. The only downside is that every time I have ordered, they come slightly out of shape. I don’t know if it’s due to the Texas heat or just being smooshed in shipping, but since it’s a malleable plastic it’s pretty easy to get fixed without any tools.

Just what I needed

I used these to connect my DSC wires from my VHF radio to my Multifunctional fish finder/Chart plotter. Since I wanted to be able to remove my electronics easily if needed, I did not want to have a permanent connections between the two devices. These four pin connectors were perfect. They are easy to install (need to be wired in) and are small enough to tuck up in small places. The are sealed and have a nice tight fit when connect to each other. The great thing is, if I need to take out my radio or chart plotter, all I have to so is un-screw the connector cap and easily pull them apart. Great product and you get plenty for other projects or if you mess up one.

- I can't fault the *quality* of these plugs; they are as described. - However, none of the descriptions are very clear unless you just happen to accidentally land upon the correct item. The reason I say that is, I need to make an extension with a PWM controller for some overly-bright LED string lights. The *wiring* is 22AWG. So I purchased these to match the wiring. - However, the *plugs* on these DO NOT FIT any of the transformer-to-cord plugs of that light string or any of my other various LED light strings. In order to get the correct size *plugs*, I have to get the ones with the 18AWG wire, which is larger. I don't know whether that size disparity will have a negative effect on the whole kit'n'kaboodle. So I thought about getting the larger size, but decided against it. - Frankly It should not be this darned difficult to find an extension for string lights, and for what standalone string light extensions cost, it would be cheaper to just buy a sacrificial set of string lights, which end up creating more unnecessary land-fill. - I'd just use a regular extension cord, except that I had wanted to include the dimmer, which must go after the transformer but before the section with the lights. - - There should not be such a big darned mystery about "extension for 2 pin single color LED outdoor string lights with transformer". I've seen a lot of comments by others who have been frustrated because things don't fit correctly, and so on. - In the end, it seems that the most straightforward thing to do will be to cut the original cord up near the transformer, and use these small-plugs-with-correctly-sized wire <!!!> to insert the extension that includes the dimmer. - I wish I'd known that in the first place instead of going bleary-eyed looking at page after page of unworkable cables.

I bought solae panel that wasn’t from Bushnell for my Bushnell trail camera, well, Bushnell is about the only company that uses a 2-pin round connector instead of a standard DC connector. I also purchased some female 5.5mm x 2.1mm connectors (link below) and it all hooks right up. The one thing I did notice … these cords come with a (red:black) pair of wires. I’m pretty sure that it’s universal that when wires are red and black, the red =(+) and black = ( - ). Well, either the connectors I bought, or these wires have the polarity crossed because I had to reverse the wires to get it to power the camera. Other than that moment of “well s*** that didn’t work”. It’s been running, uncovered, put in the woods for over a month.

Ich habe mir die 3 poligen Stecker und Buchsen zum Anschließen von Sensoren an Mikrokontroller bestellt. Die Stecker machen einen sehr robusten und hochwertigen Eindruck, die Enden werden schon verzinnt geliefert, nur beim Abisolieren hätte man etwas großzügiger sein können. Manche Stecker lassen sich etwas schwer in die Buchsen stecken aber durch die relativ großen Griffflächen ist das auch kein Problem. Mit dem Gewinde lassen sich die Stecker gut verbinden und sichern, fest angezogen sind sie dank des roten O-rings sogar wasserdicht. Die Länge von 400 mm ist für meinen Zweck perfekt. Den Preis von aktuell 8.81€ für fünf Paare halte ich für angemessen. Fazit: Fünf hochwertige Steckverbindungen zu einem fairen Preis, kann ich klar weiterempfehlen.

No llegó completo, falto una tuerca plastica

No problems and just the ticket for my project.

Beste Qualität, super passgenau verarbeitet, die Kontakte verbinden sicher und auch die Anschlusslängen sind mehr als ausreichend ! Alles in allem reicht ein Wort: PERFEKT !

Li ho comprati per connettere le luminarie di natale all'esterno di casa. Questi connettori hanno un oring e non permettono di far bagnare i contatti in caso di pioggia o umidita'. Veramente un ottimo prodotto, consigliatissimo!