24CRN

Easy to install, Works great to allow me to use the top of the tall cabinets without using a stool. I have 5 in my kitchen.

Makes it so easy to bring the contents of the cabinet down within reach. The different weight settings are great too. We used them above our washer and dryer and they work great! Highly recommend.

The media could not be loaded. The shelf is nice. It's very sturdy and well made. I'm very happy with it. The only bad thing was the instructions. It's a really short video that I had to keep stopped and restarting and The pieces aren't labeled. But it was pretty clear which was which in the video. All in all i would recommend it.

I’ve already installed two of these lifts in my 24” cabinets, so I was familiar with the assembly. This is good experience because the instructions are useless.I did modify this installation. I installed this shelf lift in a 30” wide IKEA AKURUM cabinet, over an LG Studio microwave. I had to modify it to create enough of a gap to clear the microwave. I did this by disassembling the shelf sides from the hinge and drilling new hinge mount holes 1” rear of the the original holes. When I did this, it interfered with the shelf holes in the back, so I drilled a new set of holes for the shelf, too. It clears the microwave perfectly.The other problem with this lift in the IKEA AKURUM cabinet is putting the doors back in once the lift is installed. It’s important to get it completely installed and spaced first, loosen the brackets on each side, sliding the assembly all the way over to make room, attaching the door, then repeat for the other side. Realign to original installation points and it should all just *barely* fit.I didn’t use the screws provided for the inside cabinet (template holes). They are very short. I used sturdier screws for my project.My steps.1. Modify hinges if needed. Test fit to ensure doors will close and proper clearance achieved.2. Mark template holes and pre-drill3. Secure spring hinge unit tightly to cabinet, verifying all clearance before final torque.4. Loosen spacer screws on top of hinge (narrow slots) and adjust to fit cross member brace.5. Install brace and then retighten spacer screws, ensuring even gap between cabinet and hinge6. Remove two screws on lower front of hinge and place support bracket. Screw down. Drill pilot hole for bottom. Screw down.7. Install shelves8. Install handle9. If clearance for door hinges a problem, remove lower screws from lower front brackets and loosen top spacers again.10. Slide assembly to one side, install door. Repeat for other side.11. Reposition to align bracket and replace screws. Tighten spacer screws.It may be possible to install with doors on, but you need two people for this install and the doors get in the way.

Solo trae esta tarjeta con un código qr que necesita descargues un app primero. Luego de eso escaneas el código y no te lleva al video sino a la página de compra del producto

Altogether, I bought four of these inserts. First one was to try it out, and generally, I was pleased. Enough to order three more. The first unit arrived with printed instruction on a postcard size piece of cardboard. It wasn't great, but was sufficient. The next three arrived without instructions. Only a QR code and my camera can't pick it up. So no instructions. I contacted the seller and no response. I have long ago tossed the instructions that came with the first unit. something I really regret. If anyone has a direct link to either the printable instructions (preferred) or direct link to the video, I'd be really grateful. Can't believe I'll need to return these because I have no assembly instructions, but that seems to be the case. It's not a real complicated assembly, but pretty hard to figure out with NO instructions. I was going to order two more after these units; now I'll have to look elsewhere. One star for being unwilling to fix something so easily corrected.UPDATE: finally got a response to my question about the assembly instructions, and vendor posted a direct link to the video instructions. So now it is not inconceivable that I can figure out how to put one of these units together. But the video is very difficult to work with. What is wrong with printable instructions? Perfectly OK if you don't want to send them with the product, but you should provide a link to printable instructions. I know you have them since you used to send them with your products. The video instructions are very speeded up, so difficult to get it to pause at just the second you need to see. I've upgraded to three stars overall. Five stars for the product (it really is a good product, with solid (not wire) shelving and deeper shelving than the competition plus can handle more weight than competitors) , but the instructions are at one star.

My cabinets have small fronts(edges around the opening)that are used, in part, to mount the doors. I believe this is a rather standard configuration for most cabinets. These small fronts prevent the fully assembled unit from going into place. I decided the only way to get the unit in would be by installing the unit with component as received in the box. I figured out most of the parts to assemble were on the arms. I used two stainless steel, adjustable hose clamps to force the arms to be in the extended position. Also, I shortened the measuring template by the depth of the small cabinets fronts. First I mounted the sides of shelve unit to the cabinet. Once that was done , I installed back rod. After that step, I centered the unit and tighted the slip brackets. I then installed the brace on the plates that hold the shelves. Next the shelves and the pull down rod. Next, the front brackets to the cabinet bottom. After all that, I removed the stainless stell clamps. Done. Not the "easy" they advertise. I feel it was worth the because the unit appears to be a quality product.