PumpFuse WiFi Sump Pump Monitor & Protector - No Sensors, Real-Time Alerts to Your Mobile Device: Prevent Pump Burnout, Over-Cycling & Flooding from Power Outage, Remote Control & Overload Protection

I’ve been looking for a sump pump monitor for some time and finally found one. This was easy to set up, has reliably connected to my home Wi-Fi, and has been reliable. You can set up various parameters to shut down the power, for example if the pump runs too long, or has too low of an electric load (dry running). As an example, the float on my sump pump got pinned somehow, the PumpFuse, shut off power and sent my phone an alert. Allowed me to fix the problem and prevented an expensive pump burnout.

this is a wonderful device. it allows me to monitor my sump pump with excellent notifications and worst case, i can shut it down if i need to (which i did b/c the float was stuck once). setup was a breeze. Just plugged it in and connected to the app. after that, i had to mess with all the settings, which have taken me a few months, but that should be normal as everyone has different ground conditions. best part was i able to turn off the sump entirely when it was running for too long (which the app told me). i came home and found the float was stuck. this prompted me to test the sump/float every three months to make sure it is working all the time. only thing i wish is it would integrate with homekit as a sensor so i could see it within my home app (or as a Matter device). fingers crossed this will be a new feature.

OK - You're gon’a want’a read this. I use this monitor to track our septic system discharge. This little device is fantastic and contacting their customer service got a response in minutes. We have a septic tank that pumps up and out to the leach field. The other day I flipped the wrong breaker and incorrectly shut off the septic pump. I didn’t catch it until the high water level alarm in our tank tripped. (Well OK, I actually never did catch it - the alarm did.) I realized then that I had no way of easily knowing when the septic pump ran, how many times it pumped out, how long it ran, anything. I only knew when the tank was full and then you need to scramble to fix the issue before a sewer disaster. So could I use PumpFuse to log my septic pump? YES! Problem - Our septic pump was 220VAC and Amazon specs said PumpFuse was a 125VAC device. But checking the PumpFuse website under specs said the monitor was rated 110/250VAC. So I emailed the company. Paul at PumpFuse responded - The PumpFuse device comes with a 120V plug by default. The internal circuit was tested on single phase 220V. You will need to ask your electrician to cut off the 120V plug and replace it with 220V single phase plug or use some sort of adapter or direct wire connection. Great - just what I was hoping. I ordered it. I wired it up using two adapters, plugged it in, and bingo; there was the green pair light. Connected it to our Wi-Fi and it updated its firmware. Total install time, including wiring in the adapters and connecting it to my Wi-Fi - less than 20 minutes. I can now track my septic system pumping by week, month, and year. It logs when it pumped, how long it ran, even the load drawn. This little device even has settable protection limits to shut off the pump when PumpFuse senses an unusual load but I didn't activate that function. Last night my septic pump ran at 2:27am for 13min 12sec and drew 857watts. I've only had it connected for a day so the long term reliability is unknown but for right now - Love it, Love it, Love it. So this is little thing is not just a sump pump monitor. It can also be used for septic systems and is rated for 220VAC. Thank you PumpFuse.

I need to know when my pump is running, for how long, and the frequency it turns on. The pump is the weak link in the whole septic process and its failure could mean disaster. The thought of its failure kept me up at night while out of town. This device's app provides notification of when the pump turns on/off, time it operates, power usage, long term frequency of operation and more. You can also set notifications for abnormal pumping behaviors. The app was easy to connect to the device and its been running great for over a week. I wish I had known about it long before. It works fine for my application. There are instruction videos on YouTube on how to navigate the app. Much of the app functions are relatively intuitive. There are no hard copy users' manuals. Just understand that it wouldn't work unless you have wifi/router in your home.

I purchased the PumpFuse WiFi Sump Pump monitor in September 2025 and have been using it for a few months. I am genuinely impressed with the unit because of the level of information the application provides on the activity of my sump pump. Originally, I was using a Kasa smart switch, but I became concerned about the safety of that switch due to the frequency of the on/off switching of my pump as well as the high power draw each time it cycles. The PumpFuse switch has been performing flawlessly, and my stress level is under control because the PumpFuse has an excellent array of notifications in the event trouble is encountered. I'm also impressed by the development engineering expertise with regard to the App. The user interface is well designed, easy to use and has a mind-blowing set of features and controls. Great job PumpFuse team!

I cannot say enough good things about this. I bought because I found my basement sump pump had been running nonstop due to a float switch problem. This product says it will protect the pump, shutting it off if that issue occurs. I can’t confirm that yet, but I can say this provides an INCREDIBLE amount of information about the pump. I was so impressed I bought a second one for my basement sewage ejector pump. I highly recommend pumpfuse.

This is exactly what I was looking for! After installing a sewage ejection pump , I wanted to know how often it was cycling, and how long etc. Completely unknown since we can't hear it run from our house. Not very reassuring to "assume" it's working - and just wait for the high water alarm to go off (or worse) The app works great, and logs the cycles including the run duration and date/time. One of the most reassuring features - I set it to shut off the pump if it runs more than "X" seconds - (I set it for 30 seconds - since my pump usually only runs for 15-20 seconds) So a stuck switch won't run the pump dry. I certainly don't want to have to deal with that! I feel that the pump manufacturer should have this as an option on their systems for tracking - Also - My ejection pump plugs into a "piggy back" plug for the switch - AND- this is an additional plug - so it sticks out - but I put on an extra large outdoor outlet cover, and I am able to close it OK (barely) - 5 stars so far!! Simple install with good wifi connectivity for us!

As a few other reviews put it bye Pumpspy. Ours only runs for about 3 seconds and it was hit and miss with that thing, this gets them all. You can tell it to shut off power to the pump if it runs over a value you put in the app settings to prevent pump burnout - yes we had a float stick on one running continuously. No problems with connectivity as some reviews had. Our router is only about 13 feet away. Setup was fast and easy. No subscriptions or accounts. Simple and effective. This thing is peace of mind if you worry about your basement flooding from the sump pit. We love it. Recommend.