NEIKO04207A Impact Nut & Bolt Extractor Set, 14 Piece Lug Nut Removal Tool, 3/8 Drive, Deep and Shallow Stripped Bolt Extractor Socket Set, Rounded Bolt Removal tool, Nut Remover Socket Set, CR-Mo

So pleased - a month trying to get this stripped bolt off and I was running low on transmission fluid! I don’t write many reviews but hoping this helps the next person.Ok so I had a very badly stripped differential fill Allen plug. Standard plug on a Land Rober SUV. This was semi stripped by prior mechanic and I just made it worse without the right tools. Tried the cold chisel method (you can see from photos I whacked the s&@t out of it and no luck. Bought the other stripped allen key versions on Amazon (the ones that have a slight twist in a standard looking hex/Allen to provide grip) and they just won’t get enough grip (not even close in my case so a big waste of time) if you were as badly stripped out as I was. No chance at all. I was really thinking I would need to learn to weld and go buy a welder to attach another bolt on which was going to be my last resort…Tried this and worked extremely well (was done in 20 minutes) with the following comments:As you can see from the photo I used the 11/32 size which fit about a third of the way into the stripped hex differential plug loose. I tap tapped it in gently with a 3 lb hammer to get it about 2/3 of the way in. You don’t need to be poinding it in hard since these have a slight taper which makes them slightly larger as they go further in. As you can see after massively torquing it at the end while successfully remove the fill plug it was ultimately seated about. 90% down. With the large 15mm sized head you know have a solid place to add a socket with a breaker or heavy duty impact.Other comments - IMO very little chance of this snapping off as I see others concerned about - I can’t attest to the quality of the metal but the size I was able to use makes it less likely it would snap. If I were to use the smallest 5-6 (9/32 or less) of the extractors provided I would be more concerned about putting a long breaker bar but at this size no issues. I ended up having to put a 15mm socket on a two foot breaker bar / pipe to get this to finally come loose. And once it did it was literally just finger screwing the rest of it off. Amazing how a seized bolt will hold until it doesn’t. I tried my 3/8 inch (air) impact gun before the breaker bar which is a low clearance since I didn’t have a ton of space. It’s like 350 foot pounds of torque so a mid range impact and it didn’t budge this differential plug although it MAY have weakened it up a bit so my breaker bar worked easier.Best of luck of luck to those reading this but this is the best of 3-4 methods I used and wish I started here since it was easy.Last bit of advice don’t underestimate how much torque you need to get one of these seized plugs off! And if you are in a tight area and able to use one of the provided extractors with some reasonable girth a long breaker bar is the way to go…

Life saver. Don’t know how long the drill bits will last but the extractor bits seem pretty good. I was able to remove a bolt that was broken off, and one that the head was stripped and I already tried slotting with a cut off wheel. Both on a 2009 Yamaha YFZ450R.*** HAMMER THE EXTRACTOR BIT IN, and hand crank with a crescent wrench or something similar.I also use this brand for bits and they are great.

I would rate this 4 stars out of 5 because they surprised me a time or two for both good and bad reasons. The extractors do not seem to be worth anything good. They break easily. The drill bits, however, as long as you use the right ones for the application and with care, they work decently before they dull. I have yet to try and sharpen them and try again, but if I'm needing them, I typically don't have a way to sharpen them efficiently when I'm working. I'd have to run home or get a sharpener for when I'm working (I work on the road as a mobile mechanic). Of course, the smaller ones are more fragile and I get impatient, so they broke. But for small jobs at home, I'd buy them again. For the rest of my work, I'll be searching for a better quality set.

Worked well to extract a drain plug with a stripped internal hex.

First one came broken and the second one had a duplicate . Quality check isn’t a thing it seems for this product. Makes me really question the quality of the product

I bought this set to remove a corroded shower pipe threads that had broken off in the wall. Since it was unclear what size I would need, this set that comes in 1/32 size changes would give me lots of options to get those threads out. It worked! Feels heavy duty. However, have a few gripes giving them a 3 star ratng.—red plastic box arrived broken open and the extractors everywhere. Thus manufacture packaging of box that red box was in should be a little stronger. Note the manufacturer box was inside a amazon shipping box with no packing material to cushion it. My guess is due to the heavy weight of these extractors and when dropped in shippng caused to break open.—-some of the bits are not engraved deep enough to easily read the size. Which is important when you have to put them all back in order since box was broken open.—-you need to know your fractions. Extractors were labeled in. 32, 16, 8, 4ths. Thus when trying to put back in order I am doing math in my head to figure out is 11/32 bigger or smaller than 3/8s. Prefer a label in 32 and lowest fraction would be nice. Just not easy to visually see 1/32 of an inch difference.—-need to label the size of the hex end so you know what socket size to use. The large ones required a 7/8inch socket. Maybe laser that size on bottom of extractor. I am guessing most people have open area and use a crescent wrench.—the other issue is when dealing wih a shower arm thread is all I had was a deep socket in 7/8 and the extractor sunk into the socket thus, wrapped extractor with double sided carpet tape to get it to stick and not sink in and also not fall back into the wall since loose in socket.Overall, for my use I think a Wheeler Rex 87050 nipple chuck extractor would have been better, but could not find any local plumbing stores having in stock and ordering was going to take a week. Thus, Depending on your needs this is a nice specialty tool to-have on hand for those rare situations where you need to save yourself the cost of a plumber.

Great kit for the price. Withstood a pounding from my 1/2in impact and dug in to a very rounded allen bolt. As long as you’re patient these work phenomenally. Now the only trouble is to separate the hardware from the extractor.

Used these for removing a carburetor idle jet. Worked perfectly.