VViViD Wrap Cut 32ft (10M) Vinyl Wrap Edge Cutting Detailer Tape (3 Rolls + Squeegee)

Not sure to rate higher or lower. I ordered the red wrapcut tape but received 3m's knifeless tape. A superior product in my opinion. Either way, it did what I needed just wasn't what I ordered which is a little concerning because everyone may not receive the better product.

I had to put a review here for Vvivid. I ordered this item expecting to receive the Vvivid brand tape, but instead they sent me the real 3M knifeless tape - see pic. So someone at Vvivid is reading these negative reviews or I lucked out. Anyway, the 3M tape worked flawlessly if you take your time and follow instructions. I read the instructions and watched a few videos on YouTube before trying it. As for the yellow detailer tool, toss it, it's too sharp as a squeegee and too small. Perhaps as a pointing and tucking tool, anyway I didn't use it.

I used this to apply some black vinyl to an edge on my hood that causes a terrible glare. It worked well in some spots but there was a time or two where it tore the vinyl instead of cutting. After the first time I had an exacto ready to keep the tear from getting bad the second time but I'm still going to have to rewrap it when I have time because the first tear was so bad. I suppose I'll try 3M or another brand before I give up on knifeless cutting tape altogether.

I love vvivid vinyl wraps and have used many of their colors and smoked tints with great results, however their knifeless tape does not hit the mark. Although adhesion is good, which is important as you adjust the wrap, the tape does not function properly and can often leave rough edges from time to time. The less expensive brand actually works better!

Cuts well but the rope tends to rip. I wrapped the guards and fenders, used the tape with the guards, I also jus did my wing but haven't got pics yet, it definitely cuts the 3m, can be a but hard to pull because its alittle hard to grip it. Make sure the wrap is flat when its done cause I tried pulling it through a thick piece that got bunched and I broke the rope and had to use a cutter lol but otherwise for the price. Its worth it.I did end up using all of it lol

I think I am a little inexperienced and therefore I am not getting the clean result out of this product. I gave it four stars because it really holds up well, a little tough to get the strings loose and cutting through the vinyl, with practice I should get better. I am wrapping my motorcycle so there is a lot to practice with in small tight wraps.

I got this tape because I saw that coming wraps who uses alot of Vvivid products uses knifeless tape so I got this to make my wrap project easier and it was useless. The tape is hard to pull to cut the vinyl which messed things up and the cut was not the best.i was really disappointed.

I consider myself a loyal customer.Figured I'd try this out. Pretty much a waste of plastic, string, cardboard, postage and my money.Love u Vvivid!3m Preferred Installer 9+ years

the product does work, but not as good as a razer. I had to start the cut with a razer otherwise the tape just pulled up the wrap, the cut line was also rough using this. last comment is the string was hard to separate from the tape, make sure you leave lots of extra so you can play with it.

Did not stick very well, I thought I had not preped the surface properly so I went and got rubbing alcohol to decrease the surface but still did not stick in anything but a straight line. Then once I tried to use it to cut the wrap it just pulled up and made not cuts in the material.I tried a couple of times with no success.It could be user error but I feel like it is very straight forward. I do not have experience with other knifeless tapes tho

Thread doesn't separate form the tape I have tried it many times. Also thread is to the side of the tape and not in the middle so it doesn't stick properly. Cut it not very clean either.Should have bought 3m

The worst you can buy, it doesn't work at all, to the garbage directly

Works well on softer & thinner vinyl. I used Avery Dennison vinyl and it worked well for it.. the tape adhesion was secure. Initially the string took a bit to remove, but overall good and sped up the process..