Full Extension Less Noise Ball Bearing Drawer Slides, 10 Inches, 1-Pair

I purchased these slides to replace some keyboard slides at work. Other than having to drill a couple of new holes in the mounting bracket that was there already, installing the slides was very easy. I have heard feedback from the air traffic controllers who use the drawer every day, several times per day and they all LOVE the way the new slides feel and lock back into place when slid back in. You can feel the "click", as it were, though there is no "click". It's just the feel of the slides locking into place so that they don't allow the drawer to slide back out on its own. I am delighted with these slides. I really appreciated that I could get them in the 10" length. Most hardware stores only carry the 12" and longer slides, so this was an added blessing.

I've been getting into woodworking a lot over the pandemic. I built my own set of night stands. I tried the route of making my own drawer slides out of dovetails joints without much success. I decided I wanted to go with some reliable metal, ball-bearing type slides. I needed the right size for my drawers (10" slides). All the big-box retails stores near me didn't have any that size. They only sold 15" and up, and they were expensive as well. I found these on amazon and went with them. They were great! I actually mounted them on the bottom of my drawers (not the sides) and they were perfectly fine. I really like these and they're exactly what I needed. The open and close quietly and smoothly. Nothing bad to say about this product at all. If you're looking for odd sizes like a 10" drawer slide, I'd go with this.

I purchased these to make slide out shelves on a storage unit by laying them flat and attaching sheets of wood. They work great!. Hold up to the weight I need, easy close and open, all the hardware included. Very smooth and durable.

I used these drawer slides to replace some super-old and worn out slides on my computer desk. I have a slide-out keyboard tray (I hate keeping my keyboard on the desktop) and the old slides were noisy, gritty and no longer held closed in the 'shut' position. I installed these slides in a matter of a few minutes with a power drill and screwdriver. I did have to drill new mounting holes and measure out where I wanted the slides as they were significantly different than the old slides. However, the minor bit of work was worth the effort. These new slides are quiet, smooth, and most importantly for me: they hold in the closed position with a nice positive click. They come with some short countersunk phillips-head mounting screws which should work for most people's applications. I'd recommend them if you need a single pair of drawer slides for a small project. They're reasonably priced, perform well, and are easy to mount with included hardware. No instructions are included but it's incredibly straightforward if you're even remotely mechanically inclined. Very straightforward.

When the drawer slide broke on my bathroom vanity, I searched locally but was unabble to find a 12" repalcement. I checked amamzon and found the Zengest listing. It looked exactly like the original, but to help ensure and exact fit, they have a reaplacment fit guide. 24 hours after ordering i had the replacement in hand and 5 minutes and six screws later, the job was done.

Pros: - Durable, solid, smooth operation - Installation is par for slides - Full extension slide - Best price I could find, especially for a less common length (10") and it performs just as nice as the more expensive ones I've found. Cons: - For a 10" drawer, these will obviously not be used for cabinets. When fully closed, it has quite a bit of resistance in order to open the drawer. This makes it difficult to open free-standing furniture without having to hold the furniture a bit. - Didn't come with instructions. Even though I wouldn't have read them lol. Would have been helpful for first time installs though

Had these for years and worked fine until today. Removed the drawers for cleaning and when I when to install them the ball bearing slides jumped the track. Happened to two slides. One even jumped and jammed up that the half the bearings fell out. Not great quality for the long run.

I used a pair of the 10" slides to make a slide-out shelf for a cabinet. I decided to use them in an undermount configuration instead of on the sides like you normally would, and they worked perfectly. You just have to make sure the two slides are perfectly parallel and square with the shelf. They operate smoothly and silently, look nice, and are sturdy. Just mind the bit of grease or whatever on the inner parts when you have them separated. They could do with an instruction sheet just showing how to separate the parts for install. It's not hard to figure out but it's the principle of the matter.

they work fine but as you can see in the picture it 1 of the 8 slides came without the rubber soft close stopping at the end. didn't have all the hardware either

Found this product to fit well, movement is smooth, and looks to be straight with quality support. Only shortcoming is the screws are small and the smaller size of the slotted holes. I enlarged to holes slightly to fit into a prefabricated shelving unit. Minimal effort but was an extra step. Black finish also seems to be able to resist scratching, required a good amount of effort to make a mark.

These drawer slides are constructed from very thin gauge steel, and have very little rigidity and strength, I have thrown out 3 pairs already and only been in use for 2 weeks. I have since replaced with a brand from my local hardware store that were cheaper, but built for the job in hand. I would not recommend these for anything other than a 12" X 12" max drawer size whose sole purpose is holding cotton balls and fresh air.