EUREKA ERGONOMIC CPU Holder Under Desk Mount, Computer Tower Holder 360° Swivel Height & Width Adjustable, Holds up to 44 lbs, Fits Most Computer Tower, Black

I got this when I got an adjustable height desk to prevent any issues when raising or lowering it. It was easy to install (four screws into the desk underside) and holds my full size desktop PC with no issue. The "grip" of the mount slides up and down and can extend easily to fit most any PC and the hold is solid. I've checked it a couple times just to make sure it didn't loosen up over time and it hasn't. It can also rotate on the mount making checking cables very easy as well.

Well built. You can see the quality in the welds. The design is very simple and low profile. Super easy to install. It is also wide enough to fit my 8.5in wide tower unlike many others. It is a little pricey but you get what you pay for. Oh and it comes with a nice Phillips head screwdriver as a bonus. You can tell they didn’t cheap out. Overall very satisfied!

Installation was easy and it works well to keep a unit off the floor and secure. I'm using it a small form factor (not the micro PCs) and it's not as good for that. Had to do a bit of engineering with some wood in my basement to secure it in the desk mount. Bracket would not adjust in enough to secure it by itself.

This was perfect for my wife's setup at home, she has a standing motorized desk whereas I have a manual standing desk (working on fixing that soon) but this thing was perfect for what we needed. It is a bit hard to install but once you have the first screw in, it is smooth sailing after that. Still you need like 4 arms just to get the first screw in. Her desktop was a bit large for the dimensions but seemed to fit just right once I adjusted it to fit. Word of caution, it will hold your tower in the center of the bottom and WILL block air flow from the bottom of the case so keep this in mind when mounting, there is room to move a PC forward and back but only a little. If you have a large tower like my wife's, then it will sit directly on the air vents for the bottom, luckily, nearly all the air flow moves from the front to the back and top so no hard no foul.

This is probably fine for a smaller tower, but anything on the larger side is going to be really unstable. The base plate is too small and the top bracket just doesn't lock in tight enough to keep a larger tower safe.

Arrived on time. Ease of installation was less than fifteen minutes. It holds my tower and swivels for east plugging/unplugging of UBS and other accessories. I am actually thinking about getting one for my kids towers for installation under their desks.

This item fails to support the computer evenly, causing it to tilt to one side and putting strain on the screws that are holding to the desk. I combined this with a Eureka desk, which I now regret. Regrettably, the return period ended just as the “holder” completely backed out of the top side of the desk. Don’t let the photos deceive you, I promise your computer won’t sit in this effectively! Attached are photos of the damage done to the desk from the poor design.

Excellent pc holder, my pc is very strange in design so does not perfectly fit however, this is so universal that you can make it work. Very sturdy, easy to install . satisfied,

Fazit vorab: Halterung ist sehr stabil, super verarbeitet, kam schnell an und war gut verpackt. Etwas viel Plastik, aber alles macht einen hochwertigen Eindruck. Die Halterung ist variabel in der Montage und auch nach der Anbringung um 360 Grad drehbar. Etwas größer als angegeben, was in meinem Fall positiv ist. Wenn ich sehr deutsch bewertet hätte, dann hätte ich einen Stern Abzug gegeben, da die Maße in meinen Augen nicht korrekt dargestellt werden, aber da dies in meinem Fall sinnvoll ist, bin ich sehr zufrieden! —— Ich war länger auf der Suche, da ich nur einen kleinen Bereich unter meinem Tisch habe den ich zur Montage nutzen konnte. Hierfür brauchte ich eine große Gesamtlänge und eine Möglichkeit die Ausrichtung der Halterung zu ändern. Durch die 360 Grad Möglichkeit ergeben sich im wesentlich 2 verschiedene Montage Möglichkeiten. Die Außenlänge ist in beiden Varianten logischerweise gleich: 57,5 cm. A) wie auf den Bilder zu sehen. Der obere Halter des PCs steht in T-Form von der eigentlichen Stange ab und lässt sich dadurch etwas weiter nach oben schieben. -> Siehe Skizze und Bilder. Hierbei ergibt sich ein Innenmaß von 55 cm. Von der Bodenplatte bis zur unteren Kante des oberen Halters B) der obere Halter ist in der gleich ausgerichtet wie die Stange (der obere Montageteil). Dadurch kann der Halter nicht ganz bis nach oben geschoben werden. -> Siege Skizze und Bilder. Hierbei ergibt sich ein Innenmaß von 53cm. Von der Bodenplatte bis zur unteren Kante des oberen Halters. Maße meines PCs Höhe 43 cm (ohne Füße) Breite 24 cm Tiefe 49 cm Ich hatte im übrigen kurz bedenken das das Gitter an der Unterseite durch die Bodenplatte komplett verdeckt wird. Dadurch das man den pc aber mit der oberen Halterung „gradezieht“ entsteht zwischen PC Boden und Platte eine kleine Lücke bei mir, wodurch auch das kein Thema ist. Viel Spaß mit der Halterung! Kiesel

It's great, a life changer. I'll never keep a pc on the floor or desk again. Attaching to desk is a bit scary, but do it properly and you will be fine. (there are no pre drilled holes) Drill your own holes mate.

My Pc is very heavy and Medium size with water cooling GPU & CPU. This stand holds it well under my desk. I would say only buy if you can bolt it to the frame of you stand sit desk as it will rip out of cheap table tops. Fully recommended.

produit top qualité , j'aurais aimais qu'on puisse le bloquer pour pouvoir le rehausser un peux mais dans l'ensemble vraiment pas déçus du produit !

All in all it's a good product. I used it to fix my Fractal Design R5 which still weighs 17 kg. Overall the product is pretty well designed. Be careful because the height is not adjustable: the bottom plate cannot be raised to the desired height unless you put in place a artifact such as a stainless steel clamp. Despite the 6 fixing screws, I strongly recommend NOT to fix the frame in the panel of the desk unless it is solid wood or the PC is really light. On the photos, we see that I preferred to fix it to the metal frame of the desk (here an Ikea desk model BEKANT) You will need to get a drill and drill 3mm pilot holes before fixing the frame by hand with the screwdriver provided with. The frame is not easy to set up, unless you can turn the desk over. It will therefore be necessary to crawl under the latter to do the work. Once the frame is fixed, the PC must still be placed in it, which is not necessarily easy if the machine is a certain weight. It should also be noted that the machine will be able to pivot, which facilitates cleaning (the purpose of this fixing being of course to keep the PC above the ground). Finally, since the only fixing point is at the top, the whole system can oscillate slightly without this affecting its normal use.