Rumble Go - Portable Filter for Water Bottles

Now that its cold, I'm drinking lots of tea. And I was tired of making single cups of with my small filter for loose leaf tea. This has solved the problem. I can use my large mouth water bottle easily (i have 4 of various sizes) and make all the tea I want and keep it hot in the double walled bottles. Will be getting more for gifts. It is also fairly easy to clean with both ends removable. Only issue is loose tea settles in bottom cap so does require scraping out when cleaning. So I might recommend at tab on the bottom cap so the filter can be used from either end.

First off, to correct some misconceptions mentioned by some reviewers - 200 mesh is finer than 100 mesh - this filter is very fine, but still feels sturdy.I don't drink coffee, but use this to brew cacao (very tasty and healthy, you should try it). Instead of pouring cold water over it I have to use hot water for flavor extraction and it works very well when left to brew for several hours and purposely shaking it several time during the brewing process to release more of the cacao flavor and beneficial nutrients. The brewed cacao turnsout very good and so far it's the least hassle methos of brewing cacao I have found - you just have to plan ahead and not be in a hurry.

I like making A LOT of tea at once, and it's super convenient to make it in a nalgene bottle--it's okay with hot water, easy to clean, easy to take with me, makes a WONDERFUL hot water bottle until it's drinkable. Usually I just use bagged tea, but I really want something that will let me make fancy tea in my decidedly unfancy container. So I recognize that I'm already outside of the targeted design for this thing, and it's just my first time using it, but there are already a couple of things I noticed:The bottom silicon bit doesn't have any sort of drain holes. I suppose maybe they'd be too big and let grounds out in the case of coffee making? but it means the base stays filled with liquid even after you pull it out of the container. Probably just annoying when you're making cold brew coffee, excitingly dangerous with the tea. There are certainly design alternatives they could have gone with for that, good luck not making a mess any temperature you use it at.The lid is small enough to fit into a nalgene bottle comfortably, but JUST. So pulling it back out is a bit of an adventure. you also have to push it all the way into the container to pour water over it (again, presumably less hazardous when it's not boiling water, bit of an adventure when it was.). Holes in the lid to allow the water to go in there might be nice as well--even with cold water it's definitely blocking most of the mouth of the bottle so you'd have to pour very slowly.bottom has a bit of little feet on the side that make it almost as big as the top, so pulling it out of the nalgene was also a bit scary like "am I pulling too hard, will this thing fall apart midprocess and make me really sad?" and so far (2x) it hasn't, but you're still going to want to be careful about taking it out of the tube.what i'd like to see if this was really designed for tea (or hot coffee I guess): a lip on the lid to allow it to hang from the top of the bottle instead of having to be stuck in there, drainage through the bottom. But it's the first thing I've found that's actually sized well enough to go into the nalgene in the first place, so it's a start at least!(Also, i'm not a coffee drinker, but given that the base is hollow and apparently can be pushed up inside the tube for shorter bottles than mine (32 oz nalgene big mouth), the fact that it has measurements on the outside is confusing (because the amount the inside holds will depend on the height of the assembled tube?) , so probably people should not follow those especially at first.)

This summer I have become dependent on cold brew coffee. I was just putting the grounds in a jar with water, and then 24 hours later filtering through a sieve and a coffee filter - like a savage! This lets me use the same jar, but I just yoink the Rumble Go out of the jar the next day. No more panicking about making sure that I have enough filters. And the Rumble Go empties easy into the compost bucket - very green. The Rumble Go will be paired with my Nalgene bottle for glamping this month. I may not have an expensive coffee house budget - but I have very fancy coffees!I make my cold coffee with a tsp of vanilla, a tsp of stevia and a glug of good oatmilk.

It's handy for cleaning the top and the bottom come off. Doesn't make noise shaking around in a water bottle/thermos. Over time the the silicon pieces don't seal as well: the top will pop off very easily tea comes out the top and the bottom. It's hard to shake the wet tea out of the tube with out making a mess. I ended up using a smaller popsicle-stick style infuser instead.

This cold brew system is great. I’m using a 32 oz mason jar.Make sure you get the size Rumble you want. This “Rumble GO” is for 32 oz water bottles. I ended up also ordering the 64oz version for, you guessed it, making 64 oz batches.No problem, nothing wrong with an extra coffee device. But make sure your Rumble matches the container you plan on using.Go get one !

This is by far my favorite way to make coffee on the road. It'll take a couple times to get the strength right and that also depends on the size container you use. I use a wide mouth Nalgene bottle and it fits right inside the bottle with room for a Ziplock of coarse ground coffee. The double ended design makes it the easiest cleanup ever! Now I don't have to find a Starbucks for a $5 cold brew or a nasty can full of sugar from a convenience store. I absolutely love it!

I have tried this twice now, in a yeti with fine and corse ground coffee. This filter allows for coffee sediment to escape and basically creates a coffee ground infused brown liquid that is not drinkable. This was a waste of cash. Go buy an in fridge ice coffee filter and save your time and money with item. Would not buy this again