75691 Max-Frame Receiver , Black

Ok so I have a 2015 chevy colorado wt 4x4 that came with a bumper hitch. I needed to change ball size often for different trailers and so i decided to go with the receiver hitch to make that easier. The hitch fit good and was good quality.Tips - There are 8 big bolts and 2 small bolts holding the bumper and old hitch on. these will be rusted badly and you will need a long ratchet and a 21 millimeter socket for the 8 large bolts and the little ones are like a 12 or 13 mm. you should spray these through a hole in the frame area inside the rail to help with removal. These are in an area that is hard to access with a impact and they are extremely tight. they use some thread locker on them so hit them with a torch to free that up or it will be a tough battle. the 4 large bolts on the bottom were easy to remove with the large impact. the 2 center bolts have clips that will need to be put on the new piece. the old hitch ball has to come out before the bumper will come off.be sure to remove the wires that are attached to the bumper before removal. i used zip ties to reattach the wiring. i used a 3 foot 1" drive breaker bar to loosen these big bolts so get ready for some physical work if you tackle this yourself. Good luck

I’ve put two of these on 2022 and 2021 grand Cherokee L. Watch some videos on the install and they are very easy. They are well made, heavy duty. I’ve pulled trailers and slid in cargo carriers. Trailer wiring sold separately.

Fits perfectly, took my husband and a friend about 10 minutes to put on. SO easy, don't know why I didn't order it sooner. Seems sturdy, not scratches.

Very easy to install, only took about 15 minutes, and I didn’t even have to drop the spare tire since I had a gear wrench to fit in the tight space. If you want to use an impact to tighten the bolts in the back you will have to drop the spare tire. I also mounted a new 7-way/4-way pin plug and it fit the mounting bracket that is welded to the hitch and is solid.

It fit perfectly, although the pulling wires could have been a couple of inches longer, and the packaging was dismal. I had to re-paint most corners since they were missing paint, but it fit just fine. Would've been 5 stars if I didn't have to put in extra work to end up with the advertised product.

The hitch is great, realistically it will take about an hour. Be sure to remove your spare tire to make room for fish lining the bolts and plates into place. Patience is needed for that step! If you don't have a hitch lift jack, you'll need another person to help guide and lift it into place. Also torqued bolt nuts to approx 90-100lb.

This fit my 2015 Durango perfectly and works great. The factory opening in the bumper, and the cover for it works great to hide the hitch. My only complaint are the directions are a little lacking, but a quick visit to youtube found plenty of videos with good direction.

it is what they said it was , no hassel fit up , easy install , if i ever need another one , this is the place i will go , 10 thumbs up !!!!!

This hitch bolts in easily to the vehicle it is designed for. The installation was fairly quick and simple with the included instructions. I would recommend watching a video if you are unsure of your mechanical aptitude. The item arrived days earlier than expected and included all the necessary hardware to install it.You will need a drill, a hole saw, and basic mechanical tools to install this hitch. It can be a bit tricky to bolt in to place if you do not have a helper, but with a bit of elbow grease and a few cuss words I got the job done solo.Highly recommend if you want to save a few hundred dollars over the factory setup.

Instructions are pretty good, I did watch some Youtube videos on the installation which were helpful. Fits well.

Hitch came fast and so easy to install. Definitely worth the money and would purchase again. I had some questions about the product and the customer service was quick to reply and answered everything in detail!

Overall I am happy with this trailer hitch. The only issue I had was with the way it was shipped. There was almost no protection on it for shipping and because of that, there were scratches and chips in the paint. Not a big issue as it is just all black and easy to touch-up with a spray can. The real problem with the way it was shipped was that the mounting hardware was lost in transit. They told me the hardware would be in the hitch receiver but without a box or protective wrapping, it must have fallen out on route. The seller would not supply replacement parts and only issued a $50.00 credit for the lost hardware. I ordered the replacement parts online from another supplier but they cost me over $90.00 with the shipping so that wasn't great. Once I had the hardware, it was very easy to install and everything fit properly.

thing is built like a tank.Hwavy but installed fairly easily.On the ranger tremor I had to lower sapre a bit because its a bigger tire.That was the hardest part ,figuring out how to insert that dumb set up ford has for lowering the tire .but the hitch is well made ,sturdy and looks good!