LAMPHUS Off-Road ATV UTV Light Bar Mounts Mounting Bracket Mini Bar Clamp Kits [0.75"/1"/1.25" Inch] [360-Degree] [2 Stud Sizes] [Aluminium] [2 Unit] Bull Bar Roll Bar Clamp Roll Cage Clamps Mount

Great mount clamps to attach things to round roll bars or bumpers of multiple diameters! Once mounted, these are extremely sturdy. However, depending on what diameter of bars that you are mounting these to, and which size rubber fillers you need to use to fit them to those bars, the included bolts they provide to hold the 2 halves of the clamps together may be a little too short to easily thread into the other half of the clamp, especially if you use the included lock washers on the bolts right from the start. For my setup, the bolts seemed to be about 1/8" too short. - Tip: Don't use the lock washers at first. Screw the 2 halves of the clamp together tightly. Then, put a big C-Clamp on top of these clamps to hold them together. Then remove the included bolts, put on the lock washers and the included Loctite fluid on the threads, and then put the bolts back into the clamps to hold them together as designed, and then remove the C-clamp.

I had no issue with quality or installing these on my quad rack (3/4 inch tubing) for additional light. These are light duty cast aluminum brackets with rubber inserts that span several tube dimensions. That being said they will strip out easily if apply more force than snug. I did choose to use stainless hardware over the chromed provided. They are a little fussy to to install, be sure to make your rounds when tightening to allow for even clamping pressure.

Perfect for mounting lights on roll cages. Will definitely buy these again.

Service was great and the package arrived on time. I ordered twice for different projects and the first set fastened very well. However, the second set had some challenges with one of the holes beginning to strip during tightening on both brackets. The ability to adjust was great and allowed for directional control for the fog lights. As a side note, it would be great if the bolts came with a black bolt option and at least a set of longer bolts for larger items as it would help when adding the rubber inserts to protect the item. Had to mount directly without rubber inserts. Once, completed the setup was sturdy minus the issue with bolts mentioned earlier.

I'd buy these again in a minute. But, let's start with the down side: 1) The mounting posts only lock in eight positions (every 45°). If your bars are at 22.5, or something else, then these won't mount your lights in a horizontal position (see pictures) 2) The set screws are oversized for the included hex wrench! What?! But, if you have a set of hex wrenches, then this is no big deal. 3) The aluminum clamps are just a bit too wide for the flanges on the rubber spacers. Now, the good parts: a) There are two mounting posts, a long and a short. Nice touch! For my application, the short ones were just a hair too short - but the long ones are PERFECT! b) They mount up nicely, and the included rubber spacers fit a bunch of bar sizes. The butyl rubber is tough, but compresses nicely for a secure fit. c) While the finish isn't beautiful, it's as good as can be expected for the price. I didn't have to re-tap any holes, or deburr any edges. d) These clamps are solid enough that my lights don't bounce around, even on gravel. Not sure what they would do in a real off-road situation, but hopefully I'm not riding off-road at night!

CONS: Concur with other reviewers that the threads in the clamp body strip far too easily (quality & material). Followed "best practices" of setting, clamping and tightening - but the aluminum body is just too soft to take much thread torque (material) - note I was installing on a 1.25" ATV bumper tube; using a 4mm bit in a screwdriver - so no wrenches involved (installation) . Looks to me like they should provide 2 sets of allen screws, one a little longer for folks trying to mount on the max diameter tubing (1.25" for the "mini") (material). Additionally, the indents for the set screws are not quite aligned at 45/90 deg; they are slightly off - which results in the lamps being noticeably off angle when tightened. I figure their machines are slightly off at the factory. PROS: I do like the multiple mounting options, which is why I purchased these in the first place - had a difficult mounting problem on an old Kawasaki quad (alignment) and these were the only set of clamps I found that would let me put the lamps (4" LED pods) where I wanted them. If this is your problem I'd say give these a shot, use the best practices outlined and never move them again - and you might get away with it. Words in parentheses are what the robot thinks I should say...Alignment, Material, Value for money and Adhesion.

The LAMPHUS Off-Road Light Bar Mounts are solid, well-built, and very versatile for use on my Polaris Ranger midsize. Installation was straightforward, with the adjustable clamp sizes making it easy to fit securely around the roll cage. The 360-degree rotation feature is excellent, allowing you to adjust the lights in almost any direction you need. The aluminum construction gives it a durable feel while being lightweight, and it holds up well against tough conditions, even when off-roading. One thing to note is that the provided hardware was a bit limited in terms of bolt length, so I had to source my own bolts for a more customized fit. Overall, it’s a reliable mounting solution that complements the ruggedness of my UTV.

These LAMPHUS light bar mounts are solid and reliable! Fit perfectly on various roll cages, adjustable angles make installation flexible, and the aluminum construction feels heavy-duty. Perfect for off-road lighting setups. 🛻

Fitted on my CB500X easily (41mm forks) and seems extremely durable and sturdy. Simple to install. Postage was very slow however that's my only complaint.

Awesome mount, very easy to install, the threads did not gave up and they are very strong. They are a bit big, I have installed them for my phone holder under some plastic cover to the handle bar but it worked out pretty good. I recommend it.

Good

Advertised a 2" bar mount but it only fits 1.5"

Very versatile mount, providing numerous options for pipe mount in vertical or horizontal orientation. I added locktight to each of the set screws as precaution. A few days later I took off at 2am on a 1000 mile Iron Butt Ride. Full circle and back home again, mounts remained nice and tight. Very pleased with these mounts.