8AWG-3m*2

My Jimny has 2 led spot lights. They are wired into the full beam via a relay. One had stopped working and one was not fully illuminating. They were wired together and then into the relay and earth. Wiggling the earth made the illumination of the poorly performing lamp ok…so it looked like I had connection issues. Checking I found that the recommend gauge for spot lights was 16 gauge, I ordered the wire. It arrived 1 day earlier than expected. The wire is flexible (silicon outer) easy to cut and trim back the outer. I made up replacement lengths for the lights and loose fitted to test to see if the other light would work - and it did. Made all connections permanent and tested ok post instal. Note - I did use previously purchased automotive bullet connectors etc to join the wires.

Good quality wire, had no issues. Very flexible, used for car amplifier.

So, this is 8.2 feet of 12awg silicone wire, or approx 2.5m for metric people. Came in a labelled bag, and measured 2.52m in length, so around 3cm of free wire! I've not counted the individual strands, but it certainly looks and feels like the 12awg silicone wire that comes with modern lipos. With a good amount of flux and solder it easily creates good joints to common battery connectors, I'm no expert, but I quickly created an extension cable for my lipos. Had no problems handling the current/amps in my quads/rc planes. 8.2 feet is certainly enough for most jobs, and I'm sure it will keep me stocked in wire for a long while. As I say, it feels just like the wire on my hobbyking lipos, so if you are in need of some reasonably priced wire, get some of this. Not much else to say about this silicone wire, other than it does the job great!

Just needed some heat resistant wiring to rewire a couple of ovens in my bakery. This is probably a gauge over what I required, but its decent quality , multi strands and thick insulation which seem robust.

Works great and arrived quickly, worked amazingly for changing motor wires on fpv drone

I recommend.

No complaints flexes well for the thickness, looks good quality and solderd well.

Looks good quality easy to work with good length of cable. Unfortunately although it handles amps not to bad but gets really hot when has to put 12v 20amps continuous for 2hours, personally in my opinion should be rated at 10 amp for continuous operation

La entrega fué rápida y como esta es mi primera compra de este tipo de material, las expectativas tenían relación con la presentacion en el catálogo y cumple con ellas. Supongo que la calidad, el tiempo lo dirá, aunque se ve bien. Todas las cualidades que se esperan de un producto de este tipo, las tiene, por lo demás es cuestión de paciencia, cosa que en algunas ocasiones escasea pero no quiero adelantarme. Esperemos que se cumplan todas. Atentamente.

La sezione capillare dei fili lo rende sicuro per flessioni ripetute. Il raggio di piegatura non è piccolissimo (circa 1cm) ma comunque adatto allo scopo ( Fili di collegamento per misuratore elettronico). La descrizione lascia perplessi in quanto mischia lunghezza e sezione Confermo che sono due fili indipendenti rosso e nero lunghi 8.2 piedi (250cm) di sezione awg 18 (circa 1mm diametro interno e 2.5 mm esterno)

Towar niezgodny z opisem - miało być 8 mb czarnego i 8 m czerwonego a było 2x 2,5 mb ,

Ideal um dicke Lipo-Akkus zu verkabeln. Die Kabel sind sehr biegsam und die Silikonummantelung hochwertig. Einziger Kritikpunkt ist das Fehlen der metrischen Querschnittsangabe ...Google kann das aber fix umrechnen. Alles in allem perfekt für meine Anwendungen.

Helt OK, svårt med AWG mått