Gloss Metallic Chameleon Blue to Purple Color-Shift (6ft x 5ft) with Air Release

This applied seamlessly to a live edge acacia wooden coffee table. The quality is top notch, no bubbles and adhesion was perfect! The color gives and then some and it’s really a durable surface covering. I love that I discovered this vinyl, it’s so multi functional! At $11 buck per side, you can’t beat the value for your money! I highly recommend this for the DYI’ers out there! I will say the color pops best on items that are in a well lit area, as it shows the full spectrum of colors!

Used as a golf shaft wrap and it went on smoothly! If you're thinking of doing something similar, here's my process. Cut the vinyl to the proper size. for 45-47" driver, the butt end is 2" wide and the tip is 1.5". I measure the half way point at 1-3/4. Use a piece of painters tape wrapped around the shaft to ensure measurements will fit your shaft. If possible, roll the grip opening up over itself to access the shaft under the grip. Apply the shaft wrap at the butt end first; Centering the wrap with the upper side of the shaft. It doesnt matter that much as the wrap is nearly seamly when applied correctly. Press the wrap down the length of the shaft and back up. Work one side of the shaft till it is laid down smoothly around the back, then the other side in the same manner. Trim and excess from the tip end using a razor or sharp knife. Cut angle towards the ferrule and do not cut into your graphite shaft. If your shaft is steel, you have nothing to worry about on that front. Last thing, IMPORTANT! Make sure there arent any crinkles or bubbles BEFORE applying heat. I used a hair dryer set on high and went up and down the length of the shaft a few times, pressing the wrap firmly as I went around. When youre done, roll the grip back down. Wrap added 8gr to the shaft weight. Wrap does not affect playability or flex.

Beautiful!! Thick, durable, easy to adjust.

As you can see in the photo, I purchased this to cut a vinyl decal for my mobile tattoo studio. *I just cut and applied it yesterday so I can’t speak to the longevity yet, but the color shift is really great and exactly as pictured. It has just enough sparkle in it to flash but not enough to be gaudy and I like that it’s darker when out of the sunlight, making it easier to read at a distance. Because of the glossy texture I had some reservations about whether or not it would cut well on my Cricut, but I went for it and I’m glad I did because it cut perfectly and easily. It was about average to weed, not the easiest but not the worst I’ve dealt with either. Unfortunately, the transfer tape that I used was ridiculously sticky and made transferring tough. I was pleasantly surprised that throughout that process the vinyl didn’t tear at all and it was easily lifted off of the surface and placed again, while I got the alignment where I wanted it to be. It maintained a good stretch and applied easily despite the difficult time I had with the transfer tape. I’m sure if I had used tape with less grip, the process would have been simpler. All in all, I’m really happy with the quality and so far, after applying a medium amount of heat, the bond seems strong. *I’ll update this review as time goes on. I’m optimistic that this will last the 3-5 years that the manufacturer states, but time will tell.

This is great stuff 3m ,great adhesive, color is on point 👉 👈. Using to wrap my downhill mtn bike frame

Excellent product! Purchased 1‘ x 5‘ had no room for mistakes. Pretty nice if I can say so myself, will definitely purchase again. Photos are of before and after.

This paper is beautiful on my toolbox 🧰 I feel like all the stars ⭐️ are out and the way the light makes it glimmer absolutely amazing

First off, I always buy the 1ft rolls not bad at all... Now I ordered the 1.5 Ft roll there are 4 problems. 1. The vinyl roll was rolling inverted; the color rolled on the inside and the backing showing on the outside causing ripples. 2. Rolled too tightly causing the backing to creaking and pull away from the vinyl itself while rolled up 3. It is actually not 1.5 ft!!! 1.5ft is in inches is actually 18" this is 17" 4. The adhesive is not as strong as the 1ftx5ft rolls trust me I constantly by that size *I will not buy this size again worst vinyl ever!!! But the 1ft size is great

all good

Recieved the vinyl with deep scratches throughout the whole roll. Its not even usable

As a Vinyl Virgin this was my first experience wrapping panels on my Ryker. With a little experimenting and checking out videos it was easy to use and seems durable, though time will tell. It was hard to stick on sharp corners edges but was very forgiving while I stuck and restuck it. I used a heat gun to take out imperfections, stretch and set the glue and it worked well. Used the 3M knifeless tape to do shapes and it worked well to set out the pattern…no cutting on the panels. Bought more vinyl while I figure out how much I want to wrap and to make sure the color shift was the same as adjacent panels. Love the colors. Just note that whatever imperfections are on the panel itself will be more noticeable once wrapped.

There is a learning curve to this stuff, it took me awhile to get the feel for it but the more I worked with it the better I got at it. I have only done one golf cart so far but I am so happy with the results. But it was not all fun when I first started I was very frustrated.

Used this to wrap the hood on my beater Cavalier, worked very well. Have had quite a few compliments on it