Sewell Ghost Wire 2.0, Super Flat Adhesive Speaker Wire, 16 AWG, 2 Conductor, 25 ft. Spool, White

I recently redid a room and needed to run surround sound. It wasn’t planned initially so I had to find something that would run under a rug pad and rug. I searched and found Ghost Wire! Is it a bit pricey? Yes. Is it freaking worth it? Hell yeah! It’s super flat, the copper is a nice thickness and it’s STICKY! If your surface is not clean, it won’t stick well. Have a clean surface? It’s not coming off without some damage - KEEP THIS IN MIND!!Used this along a painted concrete floor. Worked exceptionally. Easy to install and put in place. I now have surround sound and you can’t even tell it’s there!You must use the connecting block! It’s designed to connect the flat wire to your speaker wire. Don’t cheap out.Highly recommend this if you need super flat, hidden wire.

I installed new laminate flooring. I did some research prior to my installation and found this wire. I wanted surround speakers on either side of my couch and this seemed to be the perfect product. Everything works as it is supposed to...well, except for the adhesive. Like many others on here, it just will not stick. I prepped the wall exactly as they instruct, but with no success. I ran this behind my baseboard and under my floor, so I am pretty much stuck with it. I will try to find a way to adhere it to the wall and paint it to blend it in. This is a really cool concept...just lacking in the adhesion department.

Choosing a strategic location for the Ghost Wire can affect its visibility. I tried to butt it against corners, door frames, and base board to minimize its visibility.Likes: It gets the job done without needing to drill through walls, floors, or ceilings and then "fish" for speaker wire behind the wall or between joists; After working out the first connection to a terminal, the rest of them were easy to do; When I connected my speakers, it worked the first time and I have had no problems with the sound; Without doing any feathering or texturing, It took a coat of paint and matched the existing wall color perfectly (I have to point out the tape to people in order to get them to notice that it's there.)Dislikes: Although we had freshly painted walls (professionally done), the adhesive likes to come loose in a few places even though it was thoroughly pressed against the wall upon installation (It's not the worst thing in the world but I don't like to see any gap between the tape and the wall); I needed a little more Ghost Wire than was on the 100' reel so I ordered another 25' which is not on a reel and had a lot more bubbling (didn't easily lay flat on the wall); At over a buck per linear foot, it is a bit too pricey to use in every room; the folded corners do have a tendency to stand out, literally.NOTE: You still need speaker wire to run from the terminals to the speakers (I have wall mounted speakers and use about 1 foot of regular wire per speaker) and from the terminals on the other end to the amplifier or other source. If you order banana plugs (either solid or braided wire) with the terminals, the plugs do not fit into the holes in the terminals and you have to use bare wire. If they would manufacture the terminals with slightly larger holes, it would be excellent. Maybe someday they will.

I use this for doing audio in places where I have to cross traffic paths. It’s no thicker than gaff tape so it’s almost unnoticeableThe only issue is the connection blocks are a little janky, I tin the speaker wire, and when installing I tape the block and cables down tight. Granted it’s made for home use not what I do, but the stuff is amazing if you don’t want to see or trip on cables

It doesn't stay stuck to my wall. I followed the instructions and watched the video beforehand. I wiped the wall with a damp microfiber to remove any dust and let it dry. I then applied the Ghost Wire starting at one end, peeling about a foot of the backing off at a time, smoothing it and rubbing it to the wall. Working the wrinkles out as I went along. Within one day, both ends of the run had about 6 inches peeling off the wall. Three days later, and both ends are now peeled off about 2 feet. Every morning I've tried to rub it back to the wall.My walls do have a very slight orange peel texture. Perhaps on a smooth finish the Ghost Wire would adhere better. I have not attempted to paint over it yet (and likely won't since it doesn't stay on). The total length of my application was 11.5 feet.Beyond the issue of it not remaining adhered, there were a couple other issues as well. First, there's about 1/8 of clear adhesive which is not covered by the white surface material running down the entire length of the roll. This is very visible (and sticky feeling). I was hoping that I could spray some wall texture over it since paint will likely not cover it correctly. I also snapped off my exposed ends when attaching the end connectors. Since the copper is very thin, any etching done with a razor blade to cleanly expose the copper strips weakens it to the point that any flex will shear it off. I had to peel back and use scissors, leaving a small flap rather than a nice clean transition. My Ghost Wire also was quite wrinkled from being rolled up. The manufacturer states that it's a known issue and recommends a heatgun/hairdryer to remedy so I expected that going inI liked the idea of this product. If it would have stayed on the wall, it would have been great. Even with the problems I had, I could see this working well if run under a carpet. I'm contemplating using a router to notch a shallow channel in the drywall and then just mud over the inserted wire.[update]A week later, and it's completely peeled off. Not an inch is left stuck to the wall. It's just hanging between the two connector blocks that are screwed in.