ST2800

One of the best tools I have bought, in a long time! Easy to use once you have your chosen length an put it together. I have since purchased the longer panels which allows me to easily rip a 8x4 sheet. Positives: The track panels appear well made (versus the cost), are pretty straight and packs neatly away in the provided bag. Even with my additionally purchased longer panels. The saw runs well along the track as long as long as you have put it together properly and is a decent tool in its self. It can handle all materials that I have cut using it. A more affordable DIY home use version of the more expensive professional types that are available so in terms of value for money - its right up there in the DIY arena. The clamps are fairly good and do work well. However, see below for the negatives on these. Although I consider the following to be the negatives, they are minor and I still gave it the well deserved 5 stars: The clamps are not all that strong and do bend if you are not careful. Looks like cheaper material has been used to keep costs down and may require a re-weld on the joints at some stage. Not an issue to me as I have a MIG welder. But weak non the less so be wary not to over tighten them. The plastic/ rubber guide strip get chewed up quite quickly if you are not careful. Mine are now all but gone but you just compensate for it when placing the panels on your piece you are cutting. It still works as intended without them. These can be replaced if you are that bothered about it. Putting the tracks together require the Allen Key for the small grub locking screws (4 per strip and 2 strips per panel) and is quite fiddly, but do clamp the pieces together well. I would prefer some sort of quick lock system, but you would pay more for that so am happy with the system it has. All in all, a great HOME USE product. My opinion is; its not a professional piece of kit by any means, but does stand up well against its vastly more expensive Pro-Use competitors.

I have the same brand track saw and bought these to cut full panels. I know it feels like a lot of money and it is, but my view is that it is well worth it. The quality and accuracy I get with these I could not match otherwise. They are solid and allow you to cut straight for 2500mm (you need to leave the first 30cm or so free to put the plunge saw) You get also two clamps very usefull and solid, as well as two sliders that go underneath to joing the two 1400mm together. Obviously to join the tracks use a long spirit level or something else to make sure you get them right. It's very easy once you try a few times. I had to gently file the shap corners of the beginning and end of tracks before using them, to ease the process of getting the plunge saw in and out but that took two minutes it's no big deal.

This is a review of the Evolution guide rail/tracks 2400mm & 1400mm. Some time ago I purchased the 2400mm track kit. Just brilliant, comparing the cost to other track manufacturers, they are very cost effective indeed. The track is true and sturdy. However, I found it a little inconvenient at times, if for example I had a piece of material about 1600 mm to cut. With both lengths of track having be joined for an extra 200mm,in order to cover the the whole cut, a great deal of track was left overhanging at both ends. So I decided to buy the the smaller kit (1400mm) in order to just extend one piece of the original track by one piece of the small kit (700mm), which would be a much better length of track to work with for that smaller piece of material. However, when it arrived the track had a bend in its width and would not line up causing the saw to jam. So it was replaced with no problems by Amazon within 2days, (which is an amazing service)? The second kit was OK, but I had trouble lining the sections up and butting the joints together. I put a straight edge along the back of the tracks and pulled them to fit to this straight edge. I could see the the cut ends on one piece were not square so by connecting the track and fitting the connection bars meant that on the joint there was a small gap on the front side of the track? So I tightened up the joining bars in this position, and it worked when making the cut? I can only assume that in manufacture, Evolution make 1400mm pieces of track and that the smaller two piece kit are those full length tracks, cut in half (700mm) on another machine, which is not as precise or accurate as the manufacturing machines track ends? If an Evolution Sliding Mitre Saw is available fitted with a multi materials cutting blade, then a simple trim on the end at a 90 degree angle would sort it, making the whole track system absolutely perfect (in my opinion anyway). Perhaps Evolution would be better off using one of their own Sliding Mitre Saws, for the track cutting, on those smaller pieces?

I bought this track after purchasing the Evolution track saw, which came with its own track (identical to this one) but much shorter. I wanted a longer, more practical setup, and this extension track does the job really well. It’s definitely not in the same league as something like Festool, but for serious DIY users or non-pros, it works surprisingly well. The sections fit together cleanly, and I didn’t encounter any of the issues others reported — no bumps at the joints, no misalignment, and the saw runs smoothly along the full length. For the price, the value is excellent, and it’s a great way to expand the capability of the Evolution saw without spending a fortune. I haven’t tried it with any other track saw it’s supposed to be compatible with.

Not used yet but great quality. Bought on a whim, hopefully come in useful soon.

Ho una circolare makita e sono perfetti. vanno bene come suporto per il taglio

Comme pour chaque produit évolution, le kit rail de guidage est sans aucun doute possible le meilleur rapport qualité prix du marché. Tout y est de bonne qualité, les serre joints sont certainement de très bonne qualité, ce qui est très rare pour ce type de kit. , le sac pour tout transporter est un peu juste, mais c’est vraiment le seul ( tout petit) défaut que j’ai pu trouver à ce kit. À acheter les yeux fermés

He comprado esta guía para mi sierra de incisión parkside performance PPTSA 20-Li A1 y encaja casi a la perfección. La goma para evitar el astillado con el corte es un poco larga para este modelo de sierra pero lo importante es que libra el aluminio, así que tras el primer uso cortamos el sobrante y sigue funcionando perfectamente. La uso principalmente para corte de tablero y con las gomas antideslizantes sin problema. Con una longitud de 2,8 metros total (dos piezas de 1,4 metros) tienes para cualquier corte prácticamente. Y el sistema de unión de las dos partes de la guía es sólido y sin holguras. Los sargentos no los he usado de momento. Son un buen complemento, pero para usar en obra es demasiado lento, y con las gomas antideslizantes (y bien apoyado) es más que suficiente.

Väskan som medföljer rymmer 4 skenor

Exactly what I thought it was . No defects. Prompt delivery